Sweet! LTS is releasing an ONVIF compatible doorbell with SD card slot and 940nm IR
- Thread starter hook3m
- Start date
so when I try to setup the recording area from the phone and save the settings, if I go back in its all mangled. If I do it from the computer via internet explorer will it apply the settings to the phone.
will that do the same job?
They are connected to different routers so that shouldn't be the issue.
Well that's the only thing I changed and it started working right after so I'm not sure then.
So just now, someone pulled into my driveway, they must have stayed in the car for a min or so.. but I got a recording of the car, and then you see the door close and the car take off.. the part of the video of them getting out of the car and walking to my doorway is missing?? WTF kind of recording device is this. Is there a way to set the PRE-POST record timeframe.
I set the masking from the internal website not from the APP, and I'm using the RCA app at the moment.
this is very typical in current firmware. i have this all the time in both of my front and rear doorbell cameras - missing middle or the end of the video for sometimes up to 1 minute. there is a guy here who sells this doorbell all the time. he has direct connection to the vendor. he may raise this issue for next firmware update.
ChasCam580
n3wb
I have the Nelly’s Doorcam NSC-DB1, Version 3.6.0.181016 with the same problems as mentioned above. Has there been a fix? After 24hrs of installation the app stopped seeing the doorcam, it didn’t alert me when someone rang my bell, but when I login to my Synology server I can see the doorcam video.
klunkerbus
Getting the hang of it
@ChasCam580 - your doorbell has likely went "offline" as far as Hik-Vision is concerned. You can verify this by logging into the url at hik-connect.com using the email address you used to create your app log-in with your app password. If it shows offline, one way to recover is to reboot the doorbell through the web interface (not the app). My "fix" to your problem is to not stream to my NVR.
Edited for clarity
Edited for clarity
Last edited:
alarmpro
n3wb
Everytime I reset my Uniden DB-1 by Holding down the side button to reboot. it changes the password to some default when logging into its webpage. I need that password for logging in and watching it live in NVMS7000. The password is not the one I selected in the app software, and it's not 12345. I have asked LTS to change it for me once and it worked, but I'd rather not keep asking. Thank you for everyone being so informative on these. I just purchased the LTS version too.
klunkerbus
Getting the hang of it
@alarmpro - Pressing the side button for the 30 seconds or so until the doorbell says "rebooting" is actually a restore to factory defaults, not just a reset. Yes, that sets the password for the doorbell back to the factory default. From info earlier in the thread, the default password is "admin" followed by the six character verification code printed on the front of your DB1. IOW, if that sticker shows AABBCC, you'd log in as user admin with a password of adminAABBCC.
The advantage that the web portal has is that you can choose three options. "Reboot", which does appear to be just a reset, without changing any parameter values. "Restore" sets all parameters to defaults EXCEPT for networking and user (ie., password). "Restore All" sets everything back to factory defaults, just like the "rebooting" does with the side button. Yes, the conflicted use of the word rebooting is confusing.
The advantage that the web portal has is that you can choose three options. "Reboot", which does appear to be just a reset, without changing any parameter values. "Restore" sets all parameters to defaults EXCEPT for networking and user (ie., password). "Restore All" sets everything back to factory defaults, just like the "rebooting" does with the side button. Yes, the conflicted use of the word rebooting is confusing.
ChasCam580
n3wb
Thanks for the update.
I'm having a problem with my time synchronization. Everything was fine until the time change and now it's off by 30 minutes. So I logged in and saw that the DST was checked (which would be correct for me) but there's a 30 minute, 60 minute, etc. bias that I can't undo. It appears this is causing it to show 30 minutes off. If i keep the DST checked and try to sync it back up using the computer time, it's fine for a while then goes back to 30 minutes off. Even with the DST off it's still 30 minutes off and I can't figure out how to fix it.
I'm also using an NVR, so that might be the issue. I just tried to fix the time with the NVR, so maybe that will help. Not sure where the correct place to fix this is and how to get it to stick.
Thanks
I'm also using an NVR, so that might be the issue. I just tried to fix the time with the NVR, so maybe that will help. Not sure where the correct place to fix this is and how to get it to stick.
Thanks
Last edited:
klunkerbus
Getting the hang of it
@Ip2b - Can you clarify how you see/notice the time discrepancy? Are you seeing it in the NVR data, or from liveview in the app, motion detection notifications, or the web portal, or...?
Sounds like you've been trying Manual Time Sync. Via the web portal, have you tried the option to sync to NTP? If so, what server, port and interval? My DB1 is set for server 216.239.35.0, NTP port 123, and an interval of 60 minutes. You could try a shorter interval.
Sounds like you've been trying Manual Time Sync. Via the web portal, have you tried the option to sync to NTP? If so, what server, port and interval? My DB1 is set for server 216.239.35.0, NTP port 123, and an interval of 60 minutes. You could try a shorter interval.
Yes, I am doing it manually. What seems to work is if I adjust it from the NVR (at least manually) via the web interface. If I adjust manually via the web interface for the actual doorbell, it reverts back to 30 minutes off. I will have to try the NTP, previous attempts were never successful. Should this be set on the NVR or actual doorbell?
klunkerbus
Getting the hang of it
I'm not familiar with changing any settings from a NVR, so I'll say the web interface for the doorbell itself.