Hi,
I have NVR from Floureon K9604-W with Hi3520D chip.
the NVR is stuck on logo screen. I did some search but I need some help how to upload firmware via tftp because via USB port it dosnt do nothing.
This the serial output:
and U-Boot
I only have .rom file provided by the company.
I have NVR from Floureon K9604-W with Hi3520D chip.
the NVR is stuck on logo screen. I did some search but I need some help how to upload firmware via tftp because via USB port it dosnt do nothing.
This the serial output:
Code:
U-Boot 2010.06-dirty (Aug 15 2013 - 10:07:00)
Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
Spi(cs1): Block:64KB Chip:16MB Name:"MX25L128XX"
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
16384 KiB hi_sfc at 0:0 is now current device
enable_mmu_accelerate
<<addr=0x84800000, size=0x40000, vobuf=0x8c000000>>
<<imgwidth=800, imgheight=600, linebytes=1600>>
decode success!!!!
<<addr=0x84900000, size=0x40000, vobuf=0x8d000000>>
<<imgwidth=720, imgheight=576, linebytes=1440>>
decode success!!!!
disable_mmu_accelerate
16384 KiB hi_sfc at 0:0 is now current device
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-3.0.8
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2472884 Bytes = 2.4 MiB
Load Address: 80008000
Entry Point: 80008000
## Loading init Ramdisk from Legacy Image at 81000000 ...
Image Name: JUAN root filesystem(27/11/2018)
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 8302592 Bytes = 7.9 MiB
Load Address: 81000000
Entry Point: 81000000
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 3.0.8 (root@lee) (gcc version 4.4.1 (Hisilicon_v100(gcc4.4-290+ucl ibc_0.9.32.1+eabi+linuxpthread)) ) #11 Thu Nov 9 11:04:26 CST 2017
CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: hi3520d
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 35560
Kernel command line: mem=140M console=ttyAMA0,115200 root=0100 init=/linuxrc mtd parts=hi_sfc:512K(U),256K(E),256K(L),512K(C),2560K(K),12M(R) ramdisk_size=8000
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 140MB = 140MB total
Memory: 127056k/127056k available, 16304k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc9000000 - 0xfe000000 ( 848 MB)
lowmem : 0xc0000000 - 0xc8c00000 ( 140 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc002d000 ( 148 kB)
.text : 0xc002d000 - 0xc0620000 (6092 kB)
.data : 0xc0620000 - 0xc064e3e0 ( 185 kB)
.bss : 0xc064e404 - 0xc06aa610 ( 369 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
NR_IRQS:128 nr_irqs:128 128
sched_clock: 32 bits at 82MHz, resolution 12ns, wraps every 52060ms
Console: colour dummy device 80x30
Calibrating delay loop... 1318.91 BogoMIPS (lpj=6594560)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
devtmpfs: initialized
xor: measuring software checksum speed
arm4regs : 1072.000 MB/sec
8regs : 802.800 MB/sec
32regs : 851.200 MB/sec
xor: using function: arm4regs (1072.000 MB/sec)
NET: Registered protocol family 16
hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
hw-breakpoint: maximum watchpoint size is 4 bytes.
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 40) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 41) is a PL011 rev2
uart:2: ttyAMA2 at MMIO 0x200a0000 (irq = 42) is a PL011 rev2
uart:3: ttyAMA3 at MMIO 0x200b0000 (irq = 43) is a PL011 rev2
bio: create slab <bio-0> at 0
raid6: int32x1 32 MB/s
raid6: int32x2 56 MB/s
raid6: int32x4 75 MB/s
raid6: int32x8 101 MB/s
raid6: using algorithm int32x8 (101 MB/s)
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource timer1
FS-Cache: Loaded
CacheFiles: Loaded
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Trying to unpack rootfs image as initramfs...
rootfs image is not initramfs (junk in compressed archive); looks like an initrd
Freeing initrd memory: 8108K
NetWinder Floating Point Emulator V0.97 (double precision)
L2cache cache controller enabled
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
DLM installed
squashfs: version 4.0 (2009/01/31) Phillip Lougher
NTFS driver 2.1.30 [Flags: R/W].
fuse init (API version 7.16)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
msgmni has been set to 263
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
brd: module loaded
loop: module loaded
Loading iSCSI transport class v2.0-870.
SCSI Media Changer driver v0.25
ahci: SSS flag set, parallel bus scan disabled
ahci ahci.0: AHCI 0001.0200 32 slots 2 ports 3 Gbps 0x3 impl platform mode
ahci ahci.0: flags: ncq sntf stag pm led clo only pmp pio slum part ccc sxs boh
scsi0 : ahci_platform
scsi1 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x10080000-0x1008ffff] port 0x100 irq 52
ata2: SATA max UDMA/133 mmio [mem 0x10080000-0x1008ffff] port 0x180 irq 52
Spi id table Version 1.22
Spi(cs1) ID: 0xC2 0x20 0x18 0xC2 0x20 0x18
SPI FLASH start_up_mode is 3 Bytes
Spi(cs1):
Block:64KB
Chip:16MB
Name:"MX25L128XX"
spi size: 16MB
chip num: 1
6 cmdlinepart partitions found on MTD device hi_sfc
Creating 6 MTD partitions on "hi_sfc":
0x000000000000-0x000000080000 : "U"
0x000000080000-0x0000000c0000 : "E"
0x0000000c0000-0x000000100000 : "L"
0x000000100000-0x000000180000 : "C"
0x000000180000-0x000000400000 : "K"
0x000000400000-0x000001000000 : "R"
Fixed MDIO Bus: probed
ata1: SATA link down (SStatus 0 SControl 300)
himii: probed
ata2: SATA link down (SStatus 0 SControl 300)
Invalid HW-MAC Address: 00:00:00:00:00:00
Set Random MAC address: 06:4A:5E:CF:85:F9
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
CSLIP: code copyright 1989 Regents of the University of California.
SLIP linefill/keepalive option.
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 53, io mem 0x100b0000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
hiusb-ohci hiusb-ohci.0: irq 54, io mem 0x100a0000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums_eneub6250
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-onetouch
usbcore: registered new interface driver ums-realtek
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
mousedev: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: multipath personality registered for level -4
md: faulty personality registered for level -5
device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
device-mapper: multipath: version 1.3.0 loaded
device-mapper: multipath round-robin: version 1.0.0 loaded
device-mapper: multipath queue-length: version 0.1.0 loaded
device-mapper: multipath service-time: version 0.2.0 loaded
device-mapper: dm-log-userspace: version 1.1.0 loaded
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
802.1Q VLAN Support v1.8
sctp: Hash tables configured (established 4096 bind 8192)
lib80211: common routines for IEEE802.11 drivers
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
RAMDISK: squashfs filesystem found at block 0
RAMDISK: image too big! (8106KiB/8000KiB)
usb 1-1: new high speed USB device number 2 using hiusb-ehci
UDF-fs: No partition found (1)
List of all partitions:
1f00 512 mtdblock0 (driver?)
1f01 256 mtdblock1 (driver?)
1f02 256 mtdblock2 (driver?)
1f03 512 mtdblock3 (driver?)
1f04 2560 mtdblock4 (driver?)
1f05 12288 mtdblock5 (driver?)
f000 512 romblock0 (driver?)
f001 256 romblock1 (driver?)
f002 256 romblock2 (driver?)
f003 512 romblock3 (driver?)
f004 2560 romblock4 (driver?)
f005 12288 romblock5 (driver?)
No filesystem could mount root, tried: ext3 ext2 ext4 cramfs squashfs vfat msdo s iso9660 ntfs fuseblk udf xfs
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(1,0)
Backtrace:
[<c0036cbc>] (dump_backtrace+0x0/0x110) from [<c04a857c>] (dump_stack+0x18/0x1c)
r6:00008000 r5:c1209047 r4:c064e8b0 r3:c06269bc
[<c04a8564>] (dump_stack+0x0/0x1c) from [<c04a85dc>] (panic+0x5c/0x17c)
[<c04a8580>] (panic+0x0/0x17c) from [<c0008f28>] (mount_block_root+0x1d8/0x218)
r3:c842bf34 r2:00000020 r1:c842bf58 r0:c059f6ff
r7:c002615c
[<c0008d50>] (mount_block_root+0x0/0x218) from [<c0009014>] (mount_root+0xac/0xc c)
r8:00000000 r7:00000013 r6:c0049080 r5:c002616c r4:00100000
[<c0008f68>] (mount_root+0x0/0xcc) from [<c00091a8>] (prepare_namespace+0x174/0x 1d4)
r4:c064e560
[<c0009034>] (prepare_namespace+0x0/0x1d4) from [<c0008458>] (kernel_init+0xe8/0 x11c)
r5:c0025244 r4:c064e500
[<c0008370>] (kernel_init+0x0/0x11c) from [<c0049080>] (do_exit+0x0/0x614)
r5:c0008370 r4:00000000and U-Boot
Code:
hisilicon # help
? - alias for 'help'
base - print or set address offset
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
bzr - bzr - buzzer sound out.
cmp - memory compare
cp - memory copy
crc32 - checksum calculation
ddrp - ddrp training tools v200
ddrt - ddr training tools v200
decjpg - jpgd - decode jpeg picture.
fatinfo - print information about filesystem
fatload - load binary file from a dos filesystem
fatls - list files in a directory (default /)
getinfo - print hardware information
go - start application at address 'addr'
help - print command description/usage
loadb - load binary file over serial line (kermit mode)
loady - load binary file over serial line (ymodem mode)
logo - logo - decode logo picture to show.
loop - infinite loop on address range
md - memory display
mii - MII utility commands
mm - memory modify (auto-incrementing address)
mtest - simple RAM read/write test
mw - memory write (fill)
nm - memory modify (constant address)
ping - send ICMP ECHO_REQUEST to network host
printenv- print environment variables
rarpboot- boot image via network using RARP/TFTP protocol
reset - Perform RESET of the CPU
saveenv - save environment variables to persistent storage
setenv - set environment variables
setvobg - setvobg - set vo backgroud color.
- setvobg [dev color]
sf - SPI flash sub-system
startgx - startgx - open graphics layer.
- startgx [layer addr stride x y w h]
startvo - startvo - open interface of vo device.
- startvo [dev type sync]
stopgx - stopgx - close graphics layer.
- stopgx [layer]
stopvo - stopvo - close interface of vo device.
- stopvo [dev]
tftp - tftp - download or upload image via network using TFTP protocol
usb - USB sub-system
usbboot - boot from USB device
version - print monitor version
hisilicon #I only have .rom file provided by the company.
