Can a old router be used as a repeater/range extender

Safari

Getting the hang of it
Joined
Jan 9, 2021
Messages
105
Reaction score
24
Location
America
I want to extend the range of my LAN setup to the end of our (almost) block long warehouse. I don't think my GB wavlink router will reach that far. I read that some wifi cameras
can function as repeaters, but I dont think my 6 Dlink cameras (I bought 6 used DCS-932 wifi cameras for $5 a piece) will function as repeaters, maybe I'm wrong. But I have access to many old used $5 routers.

What's the cheapest way to extend the wifi range of my LAN network?
 

concord

Getting comfortable
Joined
Oct 24, 2017
Messages
663
Reaction score
739
Whether a router can be used as a repeater, extender or access point depends on the router. What is the router make and model? Check the user manual is the best way to find out.

No, WiFi cameras normally don't have the ability to act as a repeater.
 

Safari

Getting the hang of it
Joined
Jan 9, 2021
Messages
105
Reaction score
24
Location
America
Whether a router can be used as a repeater, extender or access point depends on the router. What is the router make and model? Check the user manual is the best way to find out.

No, WiFi cameras normally don't have the ability to act as a repeater.
So I'm looking for a router that can also function as an access point?. I'll have to research the router before I buy it. I see many Linksys routers at a second hand store I frequent. They are loaded with cheap ethernet equipment
 

sebastiantombs

Known around here
Joined
Dec 28, 2019
Messages
11,511
Reaction score
27,690
Location
New Jersey
Relying on WiFi to act as a repeater for video cameras is a plan doomed for failure. WiFi is not designed for the constant high traffic a video camera generates. Generally more than two will constantly disconnect and Murphy says that will happen at the worst possible time.

Either invest in fiber or use a dedicated RF link like a Ubiquity Nano Loco.
 

SouthernYankee

IPCT Contributor
Joined
Feb 15, 2018
Messages
5,170
Reaction score
5,320
Location
Houston Tx
I have used an ASUS router as a wired access point (not for cameras) I use the same SSID on different channels (1,6,11) between the access point and the the main router.
DO NOT RUN SECURITY CAMERAS ON WIFI.
 

TonyR

IPCT Contributor
Joined
Jul 15, 2014
Messages
16,432
Reaction score
38,152
Location
Alabama
So I'm looking for a router that can also function as an access point?
Good advice from @sebastiantombs and @SouthernYankee but to answer one of your questions:

Most brand name and popular routers such as Asus and Netgear (and more) can be configured as an AP (Access Point) as follows:
  • Log into the router's webGUI
  • Disable DHCP
  • Assign a static IP to the router's LAN
Assuming you have another router somewhere in your network assigning IP's to your network devices, assign a static IP for the above AP in the same subnet as your router and one that is outside of your router's DHCP pool.

You would run an Ethernet cable from one of the AP's LAN ports to one of your router's LAN ports.
 

nostrawag

n3wb
Joined
Apr 6, 2021
Messages
16
Reaction score
2
Location
LDN
I want to extend the range of my LAN setup to the end of our (almost) block long warehouse. I don't think my GB wavlink router will reach that far. I read that some wifi cameras
can function as repeaters, but I dont think my 6 Dlink cameras (I bought 6 used DCS-932 wifi cameras for $5 a piece) will function as repeaters, maybe I'm wrong. But I have access to many old used $5 routers.

What's the cheapest way to extend the wifi range of my LAN network?
personally i would run a cat 5e cable between available remote ends of routers/access points and extend this way as a 'backbone'. you can then connect wifi access points on each end to extend wireless capabilities.
the other way perhaps is using DLAN points, using your electricity cabling?
 

Safari

Getting the hang of it
Joined
Jan 9, 2021
Messages
105
Reaction score
24
Location
America
Good advice from @sebastiantombs and @SouthernYankee but to answer one of your questions:

Most brand name and popular routers such as Asus and Netgear (and more) can be configured as an AP (Access Point) as follows:
  • Log into the router's webGUI
  • Disable DHCP
  • Assign a static IP to the router's LAN
Assuming you have another router somewhere in your network assigning IP's to your network devices, assign a static IP for the above AP in the same subnet as your router and one that is outside of your router's DHCP pool.

You would run an Ethernet cable from one of the AP's LAN ports to one of your router's LAN ports.
Running a ethernet cable between them is not practical. It has to be done wirelessly
 

holiday

Pulling my weight
Joined
Sep 12, 2018
Messages
273
Reaction score
182
Location
Having a holiday
how about Powerline networking ?

Use your existing electrical wiring to extend your Internet access to any room in your house.
 

Safari

Getting the hang of it
Joined
Jan 9, 2021
Messages
105
Reaction score
24
Location
America
I have used an ASUS router as a wired access point (not for cameras) I use the same SSID on different channels (1,6,11) between the access point and the the main router.
DO NOT RUN SECURITY CAMERAS ON WIFI.
The cameras will be offline LAN only. I'm going to try 4 cameras with ethernet cables and 4 over wifi. The wifi cameras only have a resolution of 240p to 480p. Will see what happens
 

Safari

Getting the hang of it
Joined
Jan 9, 2021
Messages
105
Reaction score
24
Location
America
Relying on WiFi to act as a repeater for video cameras is a plan doomed for failure. WiFi is not designed for the constant high traffic a video camera generates. Generally more than two will constantly disconnect and Murphy says that will happen at the worst possible time.

Either invest in fiber or use a dedicated RF link like a Ubiquity Nano Loco.
The Ubiquity Nano Loco looks nice, thanks
 

TonyR

IPCT Contributor
Joined
Jul 15, 2014
Messages
16,432
Reaction score
38,152
Location
Alabama
Last edited:

SouthernYankee

IPCT Contributor
Joined
Feb 15, 2018
Messages
5,170
Reaction score
5,320
Location
Houston Tx
I have posted this before.
I did a wifi test a while back with multiple 2MP cameras each camera was set to VBR, 15 FPS, 15 Iframe, 3072kbs, h.264. Using a wifi analyzer I selected the least busy channel (1,6,11) on the 2.4 GHZ band and set up a separate SSID and access point. With 3 cameras in direct line of sight of the AP about 25 feet away I was able to maintain a reasonable stable network with only intermittent signal drops from the cameras. Added a 4th camera and the network became totally unstable. Also add a lot of motion to the 3 cameras caused some more network instability. More data more instability.
The cameras are nearly continuously transmitting. So any lost packet causes a retry, which cause more traffic, which causes more lost packets.
Wifi does not have a flow control, or a token to transmit. So you devices transmit any time they want, more devices more collisions.
As a side note, it is very easy to jam a wifi network. Wifi is find for watching the bird feed but not for home surveillance and security.

The problem is like standing in a room, with multiple people talking to you at the same time about different subjects. You need to answer each person or they repeat the question.

Test do not guess.

For a 802.11G 2.4 GHZ wifi network the Theoretical Speed is 54Mbps (6.7MBs) real word speed is nearer to 10-29Mbps (1.25-3.6 MBs) for a single channel
 

Flintstone61

Known around here
Joined
Feb 4, 2020
Messages
6,587
Reaction score
10,894
Location
Minnesota USA
As an Amazon Associate IPCamTalk earns from qualifying purchases.

Safari

Getting the hang of it
Joined
Jan 9, 2021
Messages
105
Reaction score
24
Location
America
I have posted this before.
I did a wifi test a while back with multiple 2MP cameras each camera was set to VBR, 15 FPS, 15 Iframe, 3072kbs, h.264. Using a wifi analyzer I selected the least busy channel (1,6,11) on the 2.4 GHZ band and set up a separate SSID and access point. With 3 cameras in direct line of sight of the AP about 25 feet away I was able to maintain a reasonable stable network with only intermittent signal drops from the cameras. Added a 4th camera and the network became totally unstable. Also add a lot of motion to the 3 cameras caused some more network instability. More data more instability.
The cameras are nearly continuously transmitting. So any lost packet causes a retry, which cause more traffic, which causes more lost packets.
Wifi does not have a flow control, or a token to transmit. So you devices transmit any time they want, more devices more collisions.
As a side note, it is very easy to jam a wifi network. Wifi is find for watching the bird feed but not for home surveillance and security.

The problem is like standing in a room, with multiple people talking to you at the same time about different subjects. You need to answer each person or they repeat the question.

Test do not guess.

For a 802.11G 2.4 GHZ wifi network the Theoretical Speed is 54Mbps (6.7MBs) real word speed is nearer to 10-29Mbps (1.25-3.6 MBs) for a single channel
I'll take your advice and keep the wifi to only one camera, and do five over ethernet. I bought a switch as others here suggested
 

TheSwede

Pulling my weight
Joined
Dec 27, 2016
Messages
108
Reaction score
102
Location
Sweden...
Dont ! As said before.
The DCS-932 uses 2,4 ghz and they will stream continous.
It is only 3 practically usable channels on 2,4.... and 2.4 will travel long- more disturbance from neighbours
If you have more cameras on the same router/accesspoint (as you do) the channel will be crowded.

If you use a repeater it will half the bandwith since it listens and then send the same packet.

It is possible to use ex ASUS routers as mesh, then the link on 5 Ghz, it is better but not perfect.

I have a single DCS-2230 as a a single client on a AP that is about 1 meter away and it is not completely reliable, reconnects sometime.
It IS working but not as a security cam, more to se how much snow or grass it is.

Use the cameras for watching such things as wheater, mice or easy or to do a quick setup.
Or put a cable in it..

TheSwede
 

TheSwede

Pulling my weight
Joined
Dec 27, 2016
Messages
108
Reaction score
102
Location
Sweden...
Much better way to go..

Instead of installing 220/110V to the places for the cameras, maybe needing a electrician.


Buy a POE switch, buy some POE to 5v adapters.
Draw CAT5 cables yourself and connect the cameras to the cables via the adapter.
1617879651962.png

And then you have the infrastructure ready for better cameras now when you are bitten by the Camerabug ;-)
 
Last edited:

Safari

Getting the hang of it
Joined
Jan 9, 2021
Messages
105
Reaction score
24
Location
America
Dont ! As said before.
The DCS-932 uses 2,4 ghz and they will stream continous.
It is only 3 practically usable channels on 2,4.... and 2.4 will travel long- more disturbance from neighbours
If you have more cameras on the same router/accesspoint (as you do) the channel will be crowded.

If you use a repeater it will half the bandwith since it listens and then send the same packet.

It is possible to use ex ASUS routers as mesh, then the link on 5 Ghz, it is better but not perfect.

I have a single DCS-2230 as a a single client on a AP that is about 1 meter away and it is not completely reliable, reconnects sometime.
It IS working but not as a security cam, more to se how much snow or grass it is.

Use the cameras for watching such things as wheater, mice or easy or to do a quick setup.
Or put a cable in it..

TheSwede
I have one DCS- 2132, four DCS-932 and one DCS-934. I dont actually need any of them to view 100% of my designated area, my three poe Amcrest's will do that job. I got the Dlinks at a second hand store for $5 a piece so I figured I'll try to put them to use.

The DCS- 2132 will be the only camera on wifi from a distance of about 50 meters of unrestricted space. If it fails to connect I'll take it down.

Also, I'm assuming changing the channel is simply done in the router. How do I determine the channel with the least amount of traffic ?, or are throse channels 1, 6 or 11 as SouthernYankee stated?
 
Top