Recent content by Igroup

Well, download is 50Mb and Upload is 5 Mb. No caps. Looking to get only 3 cameras on substream, or all. I should be fine, I assume. My best bet, I did not tried it, is to connect with BI to the external IP of the NVR but instead to invoke NVR's http port (8xxx) I would invoke a camera port...

No suggestions, anyone? Can I pull the NVR live view into BI? If yes, how do I do it? Individual cameras, or the whole system at once? What commands do I use? Ports? Any suggestions, at all? Thank you!

Hello, I have questions regarding setting up a NVR on location A, to BI on location B, if it's possible - locations are in different states. I have a LaView NVR new setup, model LV-KND988P86D242-T2. Comes with 4 bullet cameras model LV-PB932F4 and 2 dome LV-PD50208. These are POE. The NVR is...

After power failure, I did some tests... All softwares display "no video" but I can access all camera functions. Network works fine, I tried changing the power adapter, no results. I changed ports, port fowarding changed, no firewall, nothing happened. I do have 3 other cameras the same that...

Yes. It's been reset to defaults, also I've upgrade the firmware. Well, I'll take it down as soon as warms up outside, I will know more then.

Thanks! Yes, ptz works fine. So does any other settings from the camera through the software. It's on the network, responds fine to ping. But no video feed. It's too cold now to take it down and mess with it inside. Is it possible that camera sensor just went dead?

Nobody? No suggestions?

Hello everyone! I have a few of Mini IP PTZ HD cams, no name, with the following specs: Kernel: Linux 2.6.18_arm_v5t_le File System Version: TS48W-ONVIF-P2P V2.5.1.5 build 2014-08-21 19:49:17 It's some type of IPC, with TPSEE firmware / hardware ? I got them from AliExpress about a year ago...

Thanks. CPU is fine now, using direct to disk recording. Issue still stands with cams loosing network on BI. Around 5 minutes, like a cycle. First one cam, gets back online in 10 seconds, jumps to the other cam, back online in 10 seconds and so on all cams. In one minute all my cams go down one...

Thank you for the info. Is based on tpsee, I have up to date firmwares on all cams. I don't know if I would use TCP fix due the mix firmwares versions in there. A lot of issues mentioned there got solved. I did not tried milestone, but I did Genius Vision. Also ISpy, xeoma, sighthound and a few...

Ha, makes sense now. Just gotta figure out the ports. Check this picture: Cam 1 and 3 run on 7000 and 80 UDP. Can 2, keeps dropping, is on TCP. As the picture says, BI won't check bitrate on UDP cams, so maybe that's the answer. Due the bitrate I loose cams. Also, I mentioned above, BI...

One more update. I switched one of the camera on UDP RTP with default port 7000. Worked all night without dropping the signal. All others dropped the signal all night. I tried today to set a second camera to UDP, but it looks like I have to give it a different port than 7000. Assuming that BI...

Thank you. I followed your advice and I did change registry as I read on that forum. Still no change, same issue.

Hello, I was not able to stop the cameras from loosing signal. I did the following combinations: - on the camera, over the web, I tried vbr, cbr and cbvr. I change bitrate from 3000 to 4000 to 5000 (default). I changed i-frame to 30 and back to 100(default). I unchecked all notifications, alarm...

Thank you. I am no developer, I do networking and specialized in Microsoft architecture. That setup looks good, and from what it says, 1% CPU on a Atom is really really good. But without further explanations and or some testing, that might not be true. Leaving just Windows clean install in that...