Recent content by JordanZ
-
T54IR-AS-S3 Constant Connection Drops After Firmware Update
Rolling back the firmware didn’t correct the issue. Nothing else has changed whatsoever with the setup so no idea what is causing this. Almost appears to be at intervals but then I had a large section where it was fine. -
T54IR-AS-S3 Constant Connection Drops After Firmware Update
I have two T54IR-ASS3’s that I updated to the most recent firmware from @EMPIRETECANDY ’s website (the Sept 2024 version). Since the update, I’ve had constant drops in the feed on both on the NVR. I did a default reset and that didn’t fix anything. The stream display on my Android device running... -
Replacement Ethernet Cable for IPC-HDW4231EM
Had the network cable get damaged on one of my IPC-HDW4231EM cameras and am looking to replace the cable to save the camera. I see that the cable is glued/epoxied into the housing hole - I assume I can just drill it out? What is a replacement network cable for it? I'm seeing 12 pin 8 core? The... -
Dahua Firmware on Rebrand?
I ended up getting a free camera to product review (BV-Tech PoE IP Turret Dome Camera, UltraHD Outdoor IP Camera with Mic/Audio, Up to 98ft Night Vision, 2.8mm Lens (2K(4MP) Color) and it looks just like a IPC-T5442TM-AS-LED. I tried to upload the Dahua firmware to it from it's native GUI but... -
2022 EmpireTech Chirstmas Sales
I still haven't received anything yet - should it have arrived by now?- JordanZ
- Post #370
- Forum: EmpireTech Andy
-
NVR Swap 4xxx to 5xxx, No Cameras on List
Unfortunately there aren't any of the POE cameras showing, only my two wireless IP cameras. It's like the NVR switch isn't even assigning them IP addresses -
NVR Swap 4xxx to 5xxx, No Cameras on List
What current firmware should a NVR5232-8P-4KS2E be running? -
NVR Swap 4xxx to 5xxx, No Cameras on List
The cameras all worked fine on my 4xxx POE NVR, the issue is with this 5xxx NVR. I have previously been able to hookup a laptop to the POE port to connect and get a DHCP assignment to the 10.1.1.x range from the internal switch on the NVR, and subsequently access a camera with an IP in that... -
NVR Swap 4xxx to 5xxx, No Cameras on List
Connecting a laptop directly to the POE port I can't even get it assigned an IP address in the 10.1.1 range -
NVR Swap 4xxx to 5xxx, No Cameras on List
I tried that earlier with no success, been troubleshooting since this afternoon. The internal 5xxx POE switch is set to 10.1.1.1 / 255.255.255.0 / 10.1.1.1, which is the exact same setting as my 4xxx switch was. The cameras should connect without issue. I am wondering if there is a problem with... -
NVR Swap 4xxx to 5xxx, No Cameras on List
@EMPIRETECANDY Do you have any idea what would be causing this? -
NVR Swap 4xxx to 5xxx, No Cameras on List
As I plug them in it shows they are connected and consuming power, just nothing shows up on the camera management screen -
NVR Swap 4xxx to 5xxx, No Cameras on List
Today I plugged them all in and then turned on the NVR. On the 4xxx, I didn't do anything manually, it just recognized them as "Port 1", "Port 2" etc -
NVR Swap 4xxx to 5xxx, No Cameras on List
I recently purchased a 5xxx NVR from Andy to replace the 4xxx that I have been using forever. It has 8POE ports on the back, same as my 4xxx, but this one can handle 32 channels (I have some random IP cameras too and ran out of channels on my 4xxx). I have the new 5xxx setup on my network, can... -
gdmss plus IVS push notification not working
I will try that, it’s just frustrating because everything worked fine for years and then with these firmware updates it all went to hell. I saw another user having the same issue of transient alerts too.