Search results

  1. bigredfish

    Help required setting up new Sannce NVR

    Ok so your two NVRs are different IPs, good. So it sounds like problem is with the Virtual Host. Without seeing it and physically troubleshooting it I can't say what that is. Typically I would start but unpluggung the cameras, plugging in one at a time, and doing a manual reset while...
  2. bigredfish

    NVR5208 not booting

    Outta my league sorry
  3. bigredfish

    NVR5208 not booting

    Camera or NVR I typically hold the reset button down for 30 seconds, let go and let it reboot. I dont immediately power it down
  4. bigredfish

    Help required setting up new Sannce NVR

    No, Primary and Secondary DNS are your DNS settings. Those don't matter right now. What is the IP address and is it the same as your other NVR?
  5. bigredfish

    Empire Tech IPC-T54-ZE-S3 Stutter and problem with DMSS

    Is that DMSS on a phone, iPad? Doesnt look like DMSS Never seen that, can't help ya there
  6. bigredfish

    NVR5208 not booting

    The only time I've had one get stuck in the bootup sequence was due to a peripheral. 2X. Once with a wireless mouse, used a USB wired mouse and success. And once with a HDMI monitor. Switching to a VGA monitor allowed to bootup. Other than that I would suspect a problem with the power supply
  7. bigredfish

    Progressive Liberal Hypocrisy

    The woke mind virus has destroyed an entire generation of kids, but ultimately I blame the parents. They have turned over their parenting responsibility to the schools and the state. Why? Because of the 4 tenets of Liberalism 1- No responsibility 2- No accountability for my actions or lack...
  8. bigredfish

    Empire Tech IPC-T54-ZE-S3 Stutter and problem with DMSS

    If alerts are working, ignore it I would try the IP of the NVR as I mentioned. 192.168.3.X But frankly, if your alerts are working, your cameras dont need a gateway, the NVR is what you are seeing them through
  9. bigredfish

    SD49425XB-HNR IR manual control without logging in to the camera

    Why not login to the camera? The restriction is the NVR interface to the camera settings. You should get in a habit of using the direct camera UI to make ALL changes
  10. bigredfish

    Help required setting up new Sannce NVR

    Is this a wireless system? I cant find that model?
  11. bigredfish

    Help required setting up new Sannce NVR

    Thats your main NVR networking. Whats the IP address? Should be similar but off on the last number from your other NVR
  12. bigredfish

    US Elections (& Politics) :)

    Agreed. Either Wall it off or conquer it and implement Martial Law for about 20 years until you convert the next generation from woke liberalism , eh?
  13. bigredfish

    Help required setting up new Sannce NVR

    Somewhere on the NVR in the Networking area most likely. Dont know what that brand calls it. On Dahua NVRs it would typically be 10.1.1.1 This is the range of IPs the NVR hands out to the camera ports
  14. bigredfish

    Help required setting up new Sannce NVR

    It sounds like you have an IP conflict. The NVR has an IP address, the ports on the NVR have IP addressess also. These need to be in two completely different ranges just like it says. Find the NVR IP address under "networking" or similar, then find the Virtual Host or Virtual LAN IP range on...
  15. bigredfish

    NVR5208 not booting

    Try it without peripherals attached. Recently replace any?
  16. bigredfish

    Empire Tech IPC-T54-ZE-S3 Stutter and problem with DMSS

    Doubtful. I think its an external switch issue
  17. bigredfish

    NVR5208 not booting

    Have you tried physically shutting it down with the black power switch in back, waiting 30 seconds and flicking the switch on again?
  18. bigredfish

    Empire Tech IPC-T54-ZE-S3 Stutter and problem with DMSS

    Are the cameras plugged directly into the back of the NVR? If so, ALL cameras plugged into the NVR will have IP's of 10.1.1.X beggining with .65 for port #1 The NVR has its own built in switch. Dont mess with the camera IPs, the NVR assigns them based on what port you plug them into Dont mess...
  19. bigredfish

    Empire Tech IPC-T54-ZE-S3 Stutter and problem with DMSS

    NVR to server? No Yes they’ll work fine as you have them . No need to change camera IPs unless they are connected to an external switch
  20. bigredfish

    Malibu Fires

    They’re eating their own..
  21. bigredfish

    Funny / Satire

  22. bigredfish

    Malibu Fires

    No they can stay as long as needed
  23. bigredfish

    EmpireTech NVR8CH-8P-2AI - Setup Questions

    Only caution is the Full default will change the IP of the NVR back to 192.168.1.108 If thats the same range as your LAN no problem. If not maybe best to do regular default
  24. bigredfish

    EmpireTech NVR8CH-8P-2AI - Setup Questions

    If asked, just dont reset the cameras, just the NVR
  25. bigredfish

    EmpireTech NVR8CH-8P-2AI - Setup Questions

    Manager
  26. bigredfish

    Empire Tech IPC-T54-ZE-S3 Stutter and problem with DMSS

    You still have the checkbox for push alerts enabled on the NVR and setup email on the NVR. The cameras send both to the NVR which pushes alerts and sends the email
  27. bigredfish

    Empire Tech IPC-T54-ZE-S3 Stutter and problem with DMSS

    Yes DMSS gets its info from the NVR anyway. The alerts triggered by the camera are sent to the NVR then to DMSS
  28. bigredfish

    Malibu Fires

  29. bigredfish

    EmpireTech NVR8CH-8P-2AI - Setup Questions

    It won’t touch any settings made on the cameras themselves
  30. bigredfish

    EmpireTech NVR8CH-8P-2AI - Setup Questions

    I think that’s the latest You could try resetting it to factory default , it can be done with a click in the web gui
Top Bottom