Search results

  1. Mikentosh2017

    Cam1: No signal

    So set the router’s DHCP pool to .64 to .199?
  2. Mikentosh2017

    Cam1: No signal

    I’ll go back in and set the range from 00 to 53.
  3. Mikentosh2017

    Cam1: No signal

    I guess the camera isn’t going to show up in ipconfig.
  4. Mikentosh2017

    Cam1: No signal

  5. Mikentosh2017

    Cam1: No signal

    Yes.
  6. Mikentosh2017

    Cam1: No signal

    My sentiments too.
  7. Mikentosh2017

    Cam1: No signal

    Ok. I’m back in and there’s a video feed. A minute after shutting down 2 days ago I was thinking about opening another camera app. That’s what I did today and it worked. I went back to BI and deleted/installed a camera, like a poster previously recommended. And 1st the color bars then the...
  8. Mikentosh2017

    Cam1: No signal

    I’m shutting it down for 1 day.
  9. Mikentosh2017

    Cam1: No signal

    I wish I were more IT savvy. Although I’ve been using a home computer since ~1999, setting camera, computer and modem/router IP at the same session is new. Thanks for the attention.
  10. Mikentosh2017

    Cam1: No signal

    Since the Default Gateway (modem) is showing IPv6, I decided to log into the modem. It appears that the Device IPv4 Address .254 is outside the DHCPv4’s range of .253. Could this cause the modem to switch to an IPv6 address? Should I change the Device IPv4 Address to .222?
  11. Mikentosh2017

    Cam1: No signal

    I haven’t So I assume this changes my computer’s IP? I’ll change this to .222 and Restart.
  12. Mikentosh2017

    Cam1: No signal

    That’s an IP6 string?!! Ok. I’ll try to change it back up IP4.
  13. Mikentosh2017

    Cam1: No signal

    I’ve had the software since trialing other surveillance software.
  14. Mikentosh2017

    Cam1: No signal

    Now this must be a clue. My Default Gateway isn’t showing an IP address.
  15. Mikentosh2017

    Cam1: No signal

    I advanced from the line that indicated IPv4, as stated in the above instructions.
  16. Mikentosh2017

    Cam1: No signal

    I changed the .254 to .250 via Windows 10, restarted everything and still camera won’t connect. I couldn’t find “static” vs DHCP in my AT&T fiber router.
  17. Mikentosh2017

    Cam1: No signal

    I couldn’t find how to set to “static” but I did find this.
  18. Mikentosh2017

    Cam1: No signal

    It is.
  19. Mikentosh2017

    Cam1: No signal

    Release 5.5.9.6 (8/1/22) Amcrest be IP5M-T1179E Default Gateway 192.168.1.254 Computer 192.168.1.254 Camera 192.168.1.200
  20. Mikentosh2017

    Cam1: No signal

    8000274c. After attempting to Run as Windows service. I see to the right of the above choice “LocalSystem” which I believe it shouldn’t be. My connections to my switch may be wrong too. Is there anyway to revert BI to default and start over? Or is anybody available for TeamViewer...
  21. Mikentosh2017

    My Motion Sensor Triggers

    I found where I can sync the time with the PC. Is that what you meant? I couldn’t find “NetTime”. I didn’t see where I can change the name.
  22. Mikentosh2017

    My Motion Sensor Triggers

  23. Mikentosh2017

    My Motion Sensor Triggers

    I’m not sure my trigger settings are correct for my single camera. Can someone peruse my 2 photos to see if I checked the correct boxes?
  24. Mikentosh2017

    1st POE camera setup.

    I bou I bought this on Amazon last year and just installed it. I see a few there. Here’s one. https://www.amazon.com/dp/B07WNMR3R8/ref=cm_sw_r_cp_api_glt_fabc_69KCYHK52TCHVA81SZBY
  25. Mikentosh2017

    1st POE camera setup.

    I’m unable to log into the web GUI or the Configuration Tool. Is there a way to reset the camera to default?
  26. Mikentosh2017

    1st POE camera setup.

    So my camera is permanently mounted on an 8’ 4x4 and now I’m trying to make my way around Blue Iris. What screen do I need to be on to set IR trigger? It’s only taking daytime vids.
  27. Mikentosh2017

    1st POE camera setup.

    Bench, 5e, TIA/EIA 568B, I’ll swap again, yes
  28. Mikentosh2017

    1st POE camera setup.

    IP5M-T1179EW-36MM GS305P On my POE switch I get an amber LED (POE fault) and my camera is warm to the touch. My camera is attached to the switch and the switch is connected to the router. My W10 with Blue Iris is also connected to the router. Did I miss something?
  29. Mikentosh2017

    Previously opposed to Microsoft Windows

    Wow.
  30. Mikentosh2017

    Previously opposed to Microsoft Windows

    Yeah, that’s what I heard. With 8 too.
Top Bottom