Search results

Hello guys what's up? I have a weird problem. I have a building of four floors . Running cat6 cable from basement to each floor the max distance from basement to Fourth is not more than 40 Meter.cables are connected between fortinet poe switchs. Ok here is the problem: The Two of the cables...

OK Thanks

In that setting we can split 32 ip camera to 16 for each tvs Right?but

Hello guys what's up ? What device i need for splitting nvr 32 channel to two monitors each 16 ip camera? Split 32 channel to 16 for one tv and other 16 for the second tv . thanks

Hello guys whats up just a quick question. I have ds-7732ni-k4 nvr with Multi-address enabled feature. Nvr lan 1 connected to main router And lan 2 connected to poe switch All my ip cameras are connected to poe switch My question here will i be able to live view via hik-connect app ? Main...

Finally i got it work i had to turn off uplink wireless monitor in unifi controller then all went work.that was strange though cause to power down the ports.

Yea but but my access points are working and my ip camera is working fine

Yep computer directly connected to the router working fine and it does have internet connection. Beside i have two nvr connected to a router via lan cable and they are working fine. What I don't understand is even if the setting in my switch not configured correctly why there is no led activety...

Internet (fiber optic) to router to Smart poe switch.(my main router is GBO ONU) see the attached photo Like i said sometimes i have no probtbut sometimes i see no connection between router and poe smart Switch like there is no cable also the led on ports are off. So ihave edited your pic as my...

Hello guys what's up? I am trying to connect my ftth router to a poe smart Switch hikvision. I have 7 uap ac lite connected to a poe smart Switch and an Ethernet cable connected from my ffth router to a poe smart Switch to provide the internet to all uaps . The problem is it works some and some...

Yes all of them are enabled

Ok here are rhe photos See the link/act/poe are leds are working fine but inside the poe switch is shows everything is disconnected.

How can i do that? Bs: i cannot see topology function in ivms-4200 it even wasn't there before i upgrade it

I did complete reset and simple reset but same thing . I used this version Firmware_V1.2.0_210823 Its only the poe status is not showing its also some other features. I may post some pics tomorrow.

Ok i successfully upgraded but now port status show every port are disconnected, while in osd every used port are blinking and working. Its just a port status is not showing any Ethernet ports are connected.

Yes i did it stucks at 0% then after a few sec a message popup says upgrade failed

That's what tried

Well i am here is the model i have maybe somebody will provide a link for firmware for because i cannot find it in the hikvision website. DS-3E1318P-SI

Hello guys whats up ? I am trying to upgrade my Managed poe switch but when upgrade it says failed

Thanks i just saw that on a website thought it matters

Yes i know that. But my question was when do we use Mode A and Mode B ? Do you use Mode A or Mode B when a product vendor like a poe switch provides info on datasheet on which mode you use? Because here is what i found this info that's why i am asking

Hello guys whats up? Regarding a poe/none poe PSE(POE switch etc..) So if i have a poe switch and a poe ip camera does it matter the Ethernet cable terminator Mode ?or i should use Mode A ? because i always Mode B Or i can use any mode? Or it does matter ? If it does,does the manufacturer...

Got you so i need any kinds poe splitter as long as its an Active Poe splitter. Thanks bro

So the poe splitters doesn't have a regulators to change 48vdc to 12vdc for powering mic right?

My thought was before i surf the internet for low info about powering external mic bro

I thought without splitter i could get from Ethernet cable to power the mic

I will just go with the splitter then.

I guess i will go with the splitter since it doesn't need extra wires like this one

So in all cases i will still need a poe splitter i guess there is no way to get power from Ethernet cable cat6 connected to a poe switch without a splitter or a12 vdc adapter? I mean there is no way to power the mic with cat6 cable connected to a poe switch only? What do you mean by this one?

Hello guys whats up ? I have a question regarding ip camera type DS-2CD2143G2-IS This doesn't support mic built-in.and i cannot find any with built-in mic. I can't run extra wires or use an external power supply. I wanna add external mic to the ip camera. I have this mic and it has two rca...