Hikvision DS-KD8003-IME - New video doorbell

Hmm, I have video , but not in early call, that's why I use that originate/rtsp ...
But video works for my when there is a direct call from Doorstation to indoor trunk to extension..., maybe video not enabled? You need h264 codec enabled in PBX setting... Do you see no video at all, or black screen? I have had a black screen before , and it was an issue with the sip client, an older linphone version, they fixed that in a newer release...
 
Got it! haha.
Door station 1 has to be "0" Door stations after it 1,2,3,

Video is enabled on the PBX. I have direct video from Phone - Phone. But no direct video Doorphone to SIP phones.
 
  • Like
Reactions: NoFate
For a test, can you also configure the Doorstation as an sip client and the 93xx too? So make a direct call over sip from outdoor to indoor, I never got early video working on the indoor station, only after a pickup call, never got that to work .. that's why I used the alternative trunk approach
 
Hmmm I'm not sure how that would work. If add sip also wouldn't it ring again after the screens finish ringing.
I will test tomorrow its late here i'll be up until 8am if I can get them connected again hahaha
 
So, I think im running half SIP, half Trunk. I have to have the SIP setup in session settings for the Sub Door station to work.
And SIP to FreePBX has to be present in device configuration to get PBX calls. Doorphones - Main Station, Hik-sip. Indoor station - PBX, SIP Trunking

I still cant get video to show up on the cisco phones. I think because the cisco has H264 AES 128 I cant switch it to NONE on the phone.
I had to turn off video on the Cisco entirely because no audio would pass on both ends, even putting the call on hold no audio MOH. Other non Video phones worked fine with the Doorphone calls.
Even another trunked PBX through a 2nd hunt group had no issues with audio or DTMF on the calls.
I had claude.ai try playing with the conf file no luck on the video or audio while the phone has video enabled.

Tons of these errors on 9510 SSH:


[159981.783245] \x1b[0;33m[DDM] DEBUG [Audiopath_setPath|17] Audiopath_setPath dir 1 gpio 106 level 0 \x0a\x1b[0m
[159981.783428] \x1b[0;31m[DDM] ERROR [DDM_soundGetPath|337] Cannot match this path: 1(direction : 0)!!\x1b[0m
[159981.784079] \x1b[0;31m[DDM] ERROR [DDM_soundIoctl|536] DDM_soundGetCodecBypath failed=-5\x1b[0m
[159982.261932] \x1b[0;33m[DDM] DEBUG [Audiopath_setPath|22] Audiopath_setPath dir 1 gpio 105 level 1 \x0a\x1b[0m
[159982.261950] \x1b[0;33m[DDM] DEBUG [Audiopath_setPath|22] Audiopath_setPath dir 1 gpio 106 level 1 \x0a\x1b[0m
[159982.262122] \x1b[0;31m[DDM] ERROR [DDM_soundGetPath|337] Cannot match this path: 1(direction : 0)!!\x1b[0m
[159982.262167] \x1b[0;31m[DDM] ERROR [DDM_soundIoctl|536] DDM_soundGetCodecBypath failed=-5\x1b[0m
[159985.583286] \x1b[0;33m[DDM] DEBUG [rk809_update_bits|214] update bits same! update reg:0x38 value:0x0\x1b[0m
[159985.583304] \x1b[0;33m[DDM] DEBUG [Audiopath_setPath|17] Audiopath_setPath dir 1 gpio 105 level 0 \x0a\x1b[0m

***Fixed the issue with audio while cisco phone has video enabled
 
Last edited:
Testing again. Its possible to have the Doorphones on SIP extensions for intercom and paging, and have the Doorphone ring through the trunk for doorbell calls
Just setup a sip extension and dont add a number to call let the indoor station handle that end.
 
  • Like
Reactions: NoFate
NoFate said:
But if you setup sip on door intercom and indoor, you will loose early video on the indoor?
Click to expand...
I haven't been able to get video at all on the Cisco phones.
I had to change the conf a bit to get audio to work while the phones have video enabled.
I have audio now while the phones have video enabled on them but video doesnt work.
The other non video-phones worked fine all along.
 
Is the trunk suppose to stay unvail? its registered and working but always "Unavail"

Endpoint: Hikvision_Trunk Unavailable 0 of inf
OutAuth: Hikvision_Trunk/10000000005
Aor: Hikvision_Trunk 0
Contact: Hikvision_Trunk/sip:10000000005@192.168.1. c4711b401f Unavail nan
Transport: transport-udp-5065 udp 0 0 0.0.0.0:5065
Identify: Hikvision_Trunk/Hikvision_Trunk
Match: 192.168.1.232/32
 
How did push video from the 8003 to Linphone? I can get a video stream from the Cisco 8865 to Linphone, works perfect.
But 8003 to Linphone no video, audio only. Either direct to the 8003 ext, or by pressing the call button and answering on Linphone through the trunk.

it was the 8003 all along. I thought it had to do with Cisco encryption
 
hmm, did nothing special, just enabled video codec h264 and video enabled in linphone, video works, but only after pickup
for early video i used that rtsp hack
 
From the 8003 I have just a black screen with audio calling from Linphone to 8003

Codecs are enabled i lowered the resolution down thinking that could be it still no video :brainfart:
 
I had a black screen before too, bur that was with an older linphone version, it was fixed in the latest one (last tested more then a year ago)
 
Very weird. I haven't been able to get video over the 8003 SIP at all. Video to the indoor screen and NVR works fine.
 
ashammah said:
Very weird. I haven't been able to get video over the 8003 SIP at all. Video to the indoor screen and NVR works fine.
Click to expand...
Have you tried another sip client? There is one on play store from acrobits, I had good experiences with it
 
I cant get video at all from the 8003 on any sip app or Cisco phone.
All debugging shows video working fine but no video shows.

If I use Firmware 2.2.58 Calling the 8003 gives a busy signal and calling from 8003 to freepbx gives a constant static.
 
You must log in or register to reply here.
Top Bottom