Switch in the attic vs. homerun wiring?

Whoaru99

Pulling my weight
Dec 22, 2018
422
159
Here
For those of you that are running a number of cameras, are you running the camera cables to a switch in the attic (or wherever), then a single cable/trunk line to main switch or NIC?

Or, did you put forth the extra to put in all home runs from each cam to a patch panel?
 
Or, did you put forth the extra to put in all home runs from each cam to a patch panel?
I did that because it wasn't too much extra work. That, plus here in coastal Mid-Atlantic it's easy for attic temps to top 140'F with 100% humidity.
 
I use 4 Poe switches spread around the house, in closets. These are connected to a single standard gigi switch, which is connected to the second nic card in the bi PC.

I feel that a single large Poe switch is more likely to fail or not able to provide the power to the ir cameras.
 
For those of you that are running a number of cameras, are you running the camera cables to a switch in the attic (or wherever), then a single cable/trunk line to main switch or NIC?

Or, did you put forth the extra to put in all home runs from each cam to a patch panel?

Hi @Whoaru99

All cables go to a nice patch panel.

If you have a detached garage or building, then I would also have another patch panel + switch for that building.
 
There are pros and cons to both methods.

Remember that you need to provide power to each POE switch. So every closet or attic location where you want a switch will need to have power available. And you will have to visit all of these locations to troubleshoot or maintain the switches. And as has been mentioned, if these locations are not climate-controlled, the electronics can suffer.

But the advantages of distributing the switches around are that you need less wire, you can have lower voltage drop to each camera, and as was mentioned, you don't hav all of your eggs in one basket.

I have a few switches, but I have them all in climate-controlled areas and readily accessible.
 
Hi @Whoaru99

All cables go to a nice patch panel.

If you have a detached garage or building, then I would also have another patch panel + switch for that building.

I'm still undecided about the house as in attic or home runs. The garage is not climate controlled so no consideration for that; whatever is there will for sure bake in the summer and freeze in the winter. There will be a switch in the garage, perhaps with a fiber link to the house. Don't need fiber for the bandwidth but it does eliminate surge/spike supression consideration of a long copper line.

Not sure how "industrial" it (see below) can be for $70, but it does list a pretty wide operating temp range -22F to 149F. And, it has a SFP jack where a fiber transceiver could go.

Anyone using one: https://www.amazon.com/BV-Tech-Indu...ocphy=9020001&hvtargid=pla-571865990838&psc=1
 
Last edited:
As an Amazon Associate IPCamTalk earns from qualifying purchases.
  • Like
Reactions: J Sigmo
All cameras home-run to a 12 port patch panel on my office closet wall. Patch cords connect them to an 18 port POE switch which uplinks to my main switch. This closet already contained my networking stuff and NAS before cameras were even a thought. While I don't have AC and it can get very hot in there, it's still cooler than the attic would be. And who wants to terminate cable in an attic anyway. Also, if your POE switch were in an inaccessible place like an attic, power cycling a camera would be difficult.
 
I currently have these and I’m impressed with there performance, but the downside is they don’t provide port covers for the ports your not using.

I have the 18 port version. No complaints. I've bought many brands of switches over the year and never seen any come with RJ45 covers.
 
I have the 18 port version. No complaints. I've bought many brands of switches over the year and never seen any come with RJ45 covers.

Same here, but it does seem like something intended for a more harsh operating environment might be wise to include such.
 
I'm still undecided about the house as in attic or home runs. The garage is not climate controlled so no consideration for that; whatever is there will for sure bake in the summer and freeze in the winter. There will be a switch in the garage, perhaps with a fiber link to the house. Don't need fiber for the bandwidth but it does eliminate surge/spike supression consideration of a long copper line.

Not sure how "industrial" it (see below) can be for $70, but it does list a pretty wide operating temp range -22F to 149F. And, it has a SFP jack where a fiber transceiver could go.

Anyone using one: https://www.amazon.com/BV-Tech-Indu...ocphy=9020001&hvtargid=pla-571865990838&psc=1
Fiber is a fantastic way to eliminate spike and surge coupling and pick-up. That is especially important when making runs between separate buildings or even within large ones where ground points may well be at vastly different potentials at the moments when lightning hits nearby.
 
As an Amazon Associate IPCamTalk earns from qualifying purchases.