Search results

Opened the camera and next to the lens there was a small circuit board with a small reset button on it, held down for 20 seconds until the green LED went out and the camera was reset.

Found the reset button, was able to reset, camera works, problem solved.

Hello, I have already opened the camera, I do not immediately see a reset button there either.

Attached photo of the camera, no SD card slot available

Hello, this camera does not have an SD card, attached photo of the camera's identification sticker

Hello, I own 2 cameras Osiris OS-I2-EEN5M that I would like to reset to use with a Dahua recorder, anyone know where I can find the reset button?

Thanks for the explanation, this is what Jarrow also communicated to me.

Have a recorder with 8 channels to which a number of cameras are connected via POE, so utp cable. I still have some older cameras that I would like to connect to this recorder, is this possible? and if yes, what do I need for this? Attached photo of type of camera and recorder.

Ok bedankt, als ik de website open, komt die bij mij in het nederlands.

Heb een recorder met 8 kanalen waarop een aantal camera's zijn aangesloten via POE dus utp kabel. Heb je nog enkele oudere camera's liggen die ik zou willen aansluiten op deze recorder, kan dit? en indien ja, wat heb ik hiervoor nodig? In bijlage foto van type camera en recorder.

Nobody? I opened the camera and reset it, no change.

Heb een IPC-HDW1531S die van de ene dag op de andere niet meer overschakelt van nachtmodus (zwart/wit) naar dagmodus (kleur) wanneer ik hem opnieuw connecteer dan start hij terug op in dagmodus (kleur) wanneer het donker wordt gaat hij in nachtmodus (zwart/wit) maar de volgende dag blijft hij op...

I went to a dahua specialist with my recorder, he reset my recorder, I don't know how this happened, there is indeed not much to be found on the net, and those who can keep it apparently secret.

Doesn't help, tried several times, there is there still a battery on the other motherboard, is this battery soldered to cause the problem?

Am back, took a closer look at the contents of my recorder and there is a 2nd motherboard on which the utp connections are and I do find a J1 there, see photo, so try to reset there? and should the cameras be connected or not, have they also been given a password with the NVR?

Looked everywhere with magnifying glass on the motherboard, nowhere a J1 to be seen on this motherboard, had already seen such a movie on youtube

This is the answer I got from Dahua Benelux. If you do not remember the password of the NVR or camera, the camera does not have a reset button, and you no longer have access to the email address entered during the initial installation, or do not remember this, and you do not remember the answers...

Thanks, thought I had a good NVR and now it appears that I am nothing with it, I sent an email to the auction site where I bought it, hopefully they know where this comes from. Then take a look around to see if there is an installer in the area who might want to help me. Is it not possible to...

I even sent an email to Dahua service center and they are not willing / unable to help me.

Here is the picture.

Nowbody?

This is it.

Purchased this 8 channel recorder through an auction, it is locked with user and password. Have already tried to send a photo with qr code to get a code, get a message that they cannot read the qr code. How can I change it or go back to factory settings? There is no reset button on the motherboard.

I have tried this, it does not work.

It does not work

Ok i will try, connect the 4 together and then power on?

Here a picture of my camera, can you help me find the reset connections?

Hallo, i am living 50 km near Kortrijk. I don't know if this is even a dahua camera, I already opened it, but I can't find a pressure switch to reset, otherwise I would have already done this. If I needed to know which wires to short, I can do this too.

Hello, I chose the 2nd option and sent a qr code, received an email with the following text but never received the email with the security code. What can i do now? This is te text i received. Dear valued customer, Your password reset is well received. The password reset authorization will be...

Have a camera here that I want to reset, opened it up to see if it has a reset button on it, it is not present. Can I see it in my network but cannot log in because I do not know the password, how do I solve this? Attach the label present to the camera. Kind regards.