Search results

Laview which I believe are rebranded Hik

Grids not grades

I had to update the firmware to get the email working for motion detection. But now the cameras need to be updated because the motion detection grades aren't working right. That's why I need the IP address of each camera to update their firmware. I didn't realize this was an issue until I had...

I'll try and see how it goes. Thanks.

Will that remove a firmware update I installed as well?

I think I found the ips with angry ip tool with a laptop plugged into nvr poe port. but can't log in via I.E. they seem to ping ok if that's what they are.

My nvr only shows Mac addresses for each cam.

If I do one at a time I can see a generic ip through a search or as an Ovnif in the nvr list and log into the cam via I.E. Was hoping to have something to read all the ones plugged into the nvr. Can't even get the nvr to show on the sadp tool.

Bump. Anyone have any suggestions?

What ip search tool did you use. I can't get sadp to work with mine.

Have to update my cameras firmware. In the nvr I just see Mac addresses I assume. I have a camera hooked up to a poor injector with one and into the router and I'm using my PC which is hooked up to my router I downloaded winpcap and sadp. I open SID pay it just stays blank even when I...

I can try that next if it doesn't work. So I would reserve in the router and change the DHCP back in what - the NVR?

The cameras all list the same sender IP address, subnet mask, gateway and dns servers. They all have what seem to be different MAC addresses perhaps. I do not see different ip addresses for each camera anywhere.

Hmmm. SADP tool won't do anything when connected to NVR. Changed IP address to one in the DHCP range where I presume the cameras are and tried one near the NVR.

Set range to end 200. Attempted to change NVR IP , Subnet mask and Gateway to 192.168.1.201 and get a config save failed. It changed in the Verizon Fios router to .201 though. The IP will stay changed in NVR but Subnet and Gateway revert back to what was there before

DHCP server, Mine says it starts at 2 and ends at 254. WINS server 0.0.0.0 Lease time 1440. Mine has been changing from like 161, 162, 163, 164, 165, 166, now at 167. What would I pick and then shut off DHCP in the NVR and add the IP to the IPV4, subnet mask and gateway too/

OK I'll try that. Do I set it back to what the IP address was before when done?

Laview is telling me to update firmware on the cameras. "You will need to first connect one camera directly to the router along with a working power adapter. Thereafter, please use SADP (IP Search Tool (SADP)) to find the IP and log into the camera using the credentials:..." If I buy a POE...

I'll take a look tonight. Thanks.

How do I know what that is but also will work?

Great, I'll try that. Thanks a lot.

My internal IP address keeps changing when I unplug my NVR to move it or power loss for example which messes up my port forwarding rules. How can I stop this? My external IP seems to stay constant at least it has. I figured the DDNS setup worked on that?

Yes they are LV-PZ804N4 with an NVR LV-N5216D6E. Support says they are trying to figure it out and something may need an update but mine couldn't be the only one with the issue I would assume. Say if I draw a motion grid in a diamond pattern, it reverts to a square or rectangle of half the...

Even though I'm running this, if my internal ip address changes, would this still allow access. It seems my internal one keeps changing and I'm losing contact. Do I need to uncheck DHCP in my NVR - is that why it keeps changing or should the DDNS prevent this? I'm new to this so pardon my...

I'm confused with setting up DDNS. Should I set up and account and place it in the router or on my NVR? Or does it need to be on both devices? The choices are different in each. Laview has their own free DDNS but, I can use no-ip for example as well. I have looked online and on this forum...

I'm having a heck of a time setting up motion detection with Laview NVR and cameras. The grids won't save to what I draw them at and revert to different areas I didn't draw. I have the latest firmware they sent me to resolve another issue I had. The guides are not informative and the support...

Does anyone have a step by step guide to setting up the Laview NVR Motion Detection on the LV-N5216D6E? Their support is slow to nil. My grids won't save to what I set them at and revert to random squares or rectangles after they are done and not what I draw. The menus are confusing and there...

No error message. On NVR I just hit apply and ok, it appears to save but if I go back and look, it reverts to just a random square of grid I didn't set.

I have a Laview NVR LV-N5216... and I've tried multiple times and multiple ways of setting up motion detection alert grids and they don't save to what I set them at. I've tried on he NVR under Camera Management and via IP address over web that opens interface. Any suggestions. Firmware has...

Thanks