Bootrom start
Boot Media: SPI_NAND
Decrypt auxiliary code ...OK
Entry boot auxiliary code
Auxiliary code - v1.00
DDR code - V1.1.2 20160205
Build: Apr 19 2016 - 20:18:19
Reg Version: v1.5.1\
Reg Time: 2017/04/10 14:34:20
Reg Name: hi3798cv2dmd_hi3798cv200_DDR3-1866_1GB_16bitx2_4layers.reg
Boot auxiliary code success
Bootrom success
System startup
Relocate Boot
Jump to C code
Compressed-boot v1.0.0
Uncompress.....................Ok
System startup
Relocate Boot
Jump to C code
Fastboot 3.3.0-svn2968 (jenkins@centos235) (Jan 19 2018 - 13:54:56)
Fastboot: Version 3.3.0
Build Date: Jan 19 2018, 13:55:27
CPU: Hi3798Cv200
Boot Media: SPI-NAND
DDR Size: 1GB
Found flash memory controller hifmc100.
Nand ID: 0xEF 0xAA 0x21 0x00 0x00 0x00 0x00 0x00
maxclk:70M
Nand: WINBOND W25N01GV
Nand(HW-Auto): Block:128KB Page:2KB OOB:64B ECC:4bit/512 Chip:128MB*1
Boot Env on NAND
Env Offset: 0x00300000
Env Size: 0x00020000
Env Range: 0x00100000
SDK Version: HiSTBLinuxV100R005C00SPC031_20160601
logo........... Logo_Main!
--LT8612_Reset Success! Reset Count:0.
BMP_GetPixelFmt : 32
Cnfigure For SATA
CFG_COMBPHY: 0x1010
start_armboot LINE 599 0x1063
Hit any key to stop autoboot: 0
higmac_init(969): Get PhyId 0x1cc816
higmac_net_adjust_link(679): port_mode 0x9f
ETH1: PHY(phyaddr=0, rmii) link UP: DUPLEX=FULL : SPEED=100M
MAC: 38-AF-29-8C-43-C3
NET_autoLipDetect timeout
ETH1: PHY(phyaddr=0, rmii) link UP: DUPLEX=FULL : SPEED=100M
MAC: 38-AF-29-8C-43-C3
TFTP from server 192.168.1.10; our IP address is 192.168.1.108
Download Filename 'ID_4F06138PAZD3539.txt'.
Download to address: 0x1000000
Downloading: T T T
Retry count exceeded; starting again
NAND read: device 0 offset 0x500000, size 0x500000
5242880 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-3.18.24_hi3798cv2x
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 4969806 Bytes = 4.7 MiB
Load Address: 02000000
Entry Point: 02000000
Verifying Checksum ... OK
Loading Kernel Image from 0x16777280 to 0x33554432 ... OK
OK
ATAGS [0x00000100 - 0x000003D0], 720Bytes
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.18.24_hi3798cv2x (jenkins@centos235) (gcc version 4.9.2 20140904 (prerelease) (gcc-4.9.2 + eglibc-2.19 (Build by czyong) Mon Mar 9 14:14:50 CST 2015) ) #1 SMP Fri Jan 19 13:52:56 CST 2018, svn:8109
[ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Hisilicon
[ 0.000000] cma: Reserved 52 MiB at 0x3bc00000
[ 0.000000] cma: Reserved 4 MiB at 0x3fc00000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] DT missing boot CPU MPIDR[23:0], fall back to default cpu_logical_map
[ 0.000000] PERCPU: Embedded 10 pages/cpu @df3c2000 s10944 r8192 d21824 u40960
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 261128
[ 0.000000] Kernel command line: mem=1G console=ttyAMA0,115200 root=/dev/mtdblock3 rootfstype=squashfs rootwait mtdparts=hinand:3M(boot),2M(env),10M(kernel),54M(rootfs),10M(web),2M(custom),3M(logo),6M(logs),10M(config),8M(extend1),12M(backup),8M(extend2) mmz=ddr,0,0,50M vmalloc=500M single dh_keyboard=0 load_modules=1
[ 0.000000] ==>start:"=0 load_modules=1" use_console:1
[ 0.000000] log_buf_len individual max cpu contribution: 4096 bytes
[ 0.000000] log_buf_len total cpu_extra contributions: 12288 bytes
[ 0.000000] log_buf_len min size: 16384 bytes
[ 0.000000] log_buf_len: 32768 bytes
[ 0.000000] early log buf free: 14132(86%)
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 966456K/1048576K available (7256K kernel code, 424K rwdata, 2144K rodata, 450K init, 391K bss, 82120K reserved, 465808K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xe0000000 - 0xff000000 ( 496 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xdfc00000 ( 508 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0936528 (9402 kB)
[ 0.000000] .init : 0xc0937000 - 0xc09a7ac0 ( 451 kB)
[ 0.000000] .data : 0xc09a8000 - 0xc0a120e4 ( 425 kB)
[ 0.000000] .bss : 0xc0a120e4 - 0xc0a73edc ( 392 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:352
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000003] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[ 0.000010] Switching to timer-based delay loop, resolution 41ns
[ 0.000089] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns
[ 0.000216] Console: colour dummy device 80x30
[ 0.000228] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.000236] pid_max: default: 32768 minimum: 301
[ 0.000301] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000306] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000577] CPU: Testing write buffer coherency: ok
[ 0.000594] ftrace: allocating 23669 entries in 70 pages
[ 0.021311] 1970-1-1 0:0:0 CPU is alive
[ 0.021357] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.021401] Setting up static identity map for 0x6938b8 - 0x693910
[ 0.022786] CPU: hi3798cv200
[ 0.023160] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.023496] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.023824] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.023849] Brought up 4 CPUs
[ 0.023856] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 0.023860] CPU: All CPU(s) started in SVC mode.
[ 0.026399] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[ 0.027052] regulator-dummy: no parameters
[ 0.028460] NET: Registered protocol family 16
[ 0.028737] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.032443] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.032451] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.032467] Serial: AMBA PL011 UART driver
[ 0.032529] f8b00000.uart: ttyAMA0 at MMIO 0xf8b00000 (irq = 81, base_baud = 0) is a PL011 rev2
[ 0.446714] console [ttyAMA0] enabled
[ 0.450527] f8b02000.uart: ttyAMA1 at MMIO 0xf8b02000 (irq = 83, base_baud = 0) is a PL011 rev2
[ 0.475946] hisilicon-pcie: probe of f9860000.pcie failed with error -1
[ 0.482717] vgaarb: loaded
[ 0.485578] SCSI subsystem initialized
[ 0.489569] usbcore: registered new interface driver usbfs
[ 0.495083] usbcore: registered new interface driver hub
[ 0.500420] usbcore: registered new device driver usb
[ 0.505548] media: Linux media interface: v0.10
[ 0.510103] Linux video capture interface: v2.00
[ 0.515158] hisi_iommu_ptable_addr
![Stick Out Tongue :p :p](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7)
hy 0x1e000000 size:0x400000
[ 0.521335] hisi_iommu_err_rdaddr
![Stick Out Tongue :p :p](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7)
hy 0x1ef56800 size:0x200
[ 0.527247] hisi_iommu_err_wraddr
![Stick Out Tongue :p :p](data:image/gif;base64,R0lGODlhAQABAIAAAAAAAP///yH5BAEAAAAALAAAAAABAAEAAAIBRAA7)
hy 0x1ef56a00 size:0x200
[ 0.533270] in hisi_iommu_domain_init start
[ 0.538645] in hisi_iommu_domain_init end
[ 0.542840] Advanced Linux Sound Architecture Driver Initialized.
[ 0.549518] Switched to clocksource arch_sys_counter
[ 0.566810] NET: Registered protocol family 2
[ 0.571504] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[ [ 1.503523] f9c40000.himciv200.SD: eMMC/MMC/SD Device NOT detected!
[ 1.541972] usbcore: registered new interface driver usbhid
[ 1.547541] usbhid: USB HID core driver
[ 1.555020] hiahci-phy: registered new sata phy driver
[ 1.560490] vdd-gpu: 650 <--> 1150 mV at 880 mV
[ 1.565298] usbcore: registered new interface driver snd-usb-audio
[ 1.571630] oprofile: hardware counters not available
[ 1.576681] oprofile: using timer interrupt.
[ 1.580977] Netfilter messages via NETLINK v0.30.
[ 1.585684] nfnl_acct: registering with nfnetlink.
[ 1.590604] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.595927] arp_tables: (C) 2002 David S. Miller
[ 1.600554] TCP: cubic registered
[ 1.604266] NET: Registered protocol family 10
[ 1.609136] NET: Registered protocol family 17
[ 1.613723] Registering SWP/SWPB emulation handler
[ 1.619071] open /SigFilePartition error
[ 1.721674] ahci f9900000.hiahci: SSS flag set, parallel bus scan disabled
[ 1.728558] ahci f9900000.hiahci: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode
[ 1.737254] ahci f9900000.hiahci: flags: ncq sntf stag pm led clo only pmp fbs slum part ccc sxs boh
[ 1.746926] scsi host0: ahci_platform
[ 1.750758] ata1: SATA max UDMA/133 mmio [mem 0xf9900000-0xf9900fff] port 0x100 irq 102
[ 1.765568] libphy: higmac_mii_bus: probed
[ 1.769724] libphy: get_phy_device phyid 0x1cc816
[ 1.775086] Higmac dma_sg_phy: 0x3fc7a000
[ 1.780022] ALSA device list:
[ 1.782988] No soundcards found.
[ 2.077529] ata1: SATA link down (SStatus 0 SControl 320)
[ 2.084158] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 2.091416] Freeing unused kernel memory: 448K (c0937000 - c09a7000)
BusyBox v1.18.4 (2018-01-19 14:11:32 CST) built-in shell (ash)
Revision: 29708
Enter 'help' for a list of built-in commands.
~ # [ 10.269526] 1970-1-1 0:0:10 CPU is alive
[ 20.273520] 1970-1-1 0:0:20 CPU is alive
[ 30.277520] 1970-1-1 0:0:30 CPU is alive
[ 40.281520] 1970-1-1 0:0:40 CPU is alive
[ 50.285520] 1970-1-1 0:0:50 CPU is alive
[ 60.289521] 1970-1-1 0:1:0 CPU is alive
[ 70.293520] 1970-1-1 0:1:10 CPU is alive
[ 80.297520] 1970-1-1 0:1:20 CPU is alive
[ 90.301520] 1970-1-1 0:1:30 CPU is alive
[ 100.305520] 1970-1-1 0:1:40 CPU is alive
[ 110.309520] 1970-1-1 0:1:50 CPU is alive
[ 113.713520] creat /var/tmp/envState error
[ 120.313520] 1970-1-1 0:2:0 CPU is alive
[ 130.317520] 1970-1-1 0:2:10 CPU is alive
[ 140.321520] 1970-1-1 0:2:20 CPU is alive
[ 150.325520] 1970-1-1 0:2:30 CPU is alive
[ 160.329520] 1970-1-1 0:2:40 CPU is alive
Bootrom start
Boot Media: SPI_NAND
Decrypt auxiliary code ...OK
Entry boot auxiliary code
Auxiliary code - v1.00
DDR code - V1.1.2 20160205
Build: Apr 19 2016 - 20:18:19
Reg Version: v1.5.1\
Reg Time: 2017/04/10 14:34:20
Reg Name: hi3798cv2dmd_hi3798cv200_DDR3-1866_1GB_16bitx2_4layers.reg
Boot auxiliary code success
Bootrom success
System startup
Relocate Boot
Jump to C code
Compressed-boot v1.0.0
Uncompress.....................Ok
System startup
Relocate Boot
Jump to C code
Fastboot 3.3.0-svn2968 (jenkins@centos235) (Jan 19 2018 - 13:54:56)
Fastboot: Version 3.3.0
Build Date: Jan 19 2018, 13:55:27
CPU: Hi3798Cv200
Boot Media: SPI-NAND
DDR Size: 1GB
Found flash memory controller hifmc100.
Nand ID: 0xEF 0xAA 0x21 0x00 0x00 0x00 0x00 0x00
maxclk:70M
Nand: WINBOND W25N01GV
Nand(HW-Auto): Block:128KB Page:2KB OOB:64B ECC:4bit/512 Chip:128MB*1
Boot Env on NAND
Env Offset: 0x00300000
Env Size: 0x00020000
Env Range: 0x00100000
SDK Version: HiSTBLinuxV100R005C00SPC031_20160601
logo........... Logo_Main!
-