Dahua Starlight Recessed Dome PTZ (SD52C225U-HNI)

Version tab from Dahua interface
Cam firmwares Dahua.jpg

randy
 
Totally confused, it appears your SW ver is older than what I have, but your PTZ ver is newer than what I have even though the camera says its up to date.
 
dwfj, post #182 in this thread solved the problem for me. Essentially, had to use admin/admin as the user/Password combo on the "Network IP camera configuration". This is even though I changed the admin password to something else.
This my camera's software which is what it shipped with over a year ago: upload_2018-8-7_23-28-15.png
 
I was playing around with the camera settings last night and noticed a separate tab for the ONVIF account. When I changed those creds and did the 'find/inspect' , the return came back fully populated and now PTZ works ok. Exactly as posted in #182.
This camera replaced a DH-SD29A204SN-GN. That unit did not have any way to change the ONVIF creds, so the only way it would connect to BI was using admin,admin. (I didn't know at the time why that was so). That always bothered me, wondering if there were other backdoor combinations that could also be used to gain access (similar to what @nayr has talked about). I think the username/password setup in BI should be documented more clearly, or maybe it is, but I didn't understand it.
 
  • Like
Reactions: looney2ns
Hello,

I consider buying this camera to identify people and read plates at approx. 80 meters ahead.

Do you confirm this model should be a good choice ?

For night visions at x25 full zoom , should i need to add an extra IR canon or it should not be usefull ?

Thank you for advices and your experience on that one.
Regards,
 
Hello,

I consider buying this camera to identify people and read plates at approx. 80 meters ahead.

Do you confirm this model should be a good choice ?

For night visions at x25 full zoom , should i need to add an extra IR canon or it should not be usefull ?

Thank you for advices and your experience on that one.
Regards,

Please see the LPR subject area of this forum. License plate capture is an art.
 
Will do, but i don't want to use LPR with this camera i just want to visualize plates ( not list / capture them )

What do you think about the need to use and extra IR source with this camera when zooming at x25 , would it help to have one or camera sensibility should be enough ?

Thanks for your comments and help,
 
Hello,

I consider buying this camera to identify people and read plates at approx. 80 meters ahead.

Do you confirm this model should be a good choice ?

For night visions at x25 full zoom , should i need to add an extra IR canon or it should not be usefull ?

Thank you for advices and your experience on that one.
Regards,
OK, so I grabbed an image from the cam when zoomed out, then another one zoomed in on the car across the street, both using available light
 

Attachments

  • IMG_0086.jpg
    IMG_0086.jpg
    302.5 KB · Views: 179
  • IMG_0087.jpg
    IMG_0087.jpg
    107 KB · Views: 178
Thank you dwfj

I would say the car in the picture you sent is at approx. maximum 30m far from the camera, resolution is not so bad.
 
I know, that domes are not recommended for outside, but if it is under the roof out of direct sunlight, it should be OK?
 
Anybody?
 

One of the reasons that domes and not recommended for outside use are mainly three reasons..

1) Sun glare onto the dome
2) Water droplets cause reflection on the dome.
3) Direct sunlight dome causes discolouration (bit like warn front headlight glass that turns yellow)

If your cameras are away from sunlight and rain drops you will be fine to use them outside.

*EDIT for wrong number
 
  • Like
Reactions: looney2ns
Thanks for that. In Los Angeles is not much rain, but we have a lot of sunshine. So, glare would be my main concern.
I'm considering a PTZ camera, but this one won't fit under my roof(+ the above issues), there is not enough depth and SD49225T-HN is huge.
 
So i have some presets set up for the camera to go to at specific times. Today I just wanted to watch preset 4 all day. I turned off idle time, and I turned off the schedule but no matter what it always resets to preset 1. I even set preset 4 as the reboot goto and restarted both the camera and PTZ. It still ends up on preset 1... Anyone else having issues with this?
 
So i have some presets set up for the camera to go to at specific times. Today I just wanted to watch preset 4 all day. I turned off idle time, and I turned off the schedule but no matter what it always resets to preset 1. I even set preset 4 as the reboot goto and restarted both the camera and PTZ. It still ends up on preset 1... Anyone else having issues with this?
You might want to set the cam to factory defaults and start over fresh.
 
can someone provide me with the latest firmware, trying to unbricked my cam using the serial method.
any help would be much appreciated.