Menu
What's new

R0 / DS-2CD2x32 BrickfixV2 brick recovery and full upgrade tool - enhanced.

D

Dropout3228

n3wb
Joined
Jan 10, 2024
Messages
1
Reaction score
0
Location
Melbourne, Australia
I hope someone can help me with this.

I have a few Hikvision cameras (DS-2XMG222G0-ID(AE)) that I tried to upgrade the firmware using Postman. The upgrade was successful many times with the response being “Reboot Required” and I called another API to perform the reboot. I was flashing the same firmware multiple times to test the API. The version was V1.3.6.

However, once, I got a connection reset error and the camera just died and did not turn on. The next day, another camera died and wouldn't power on at all. These cameras had a static IP on the network and were plugged into an NVR (DS-MP7608HN) with it also being connected to the network. Today, two more cameras died while upgrading. I didn't get any response, just a “Connection Reset. Unexpected end of stream” in the logs.

I tried to do the method listed here, but I don't get any response on the TFTP at all. I also followed Wendell's step and used Scott's script but no luck at all. Furthermore, I am not able to detect the cameras at all. Nothing happens on the TFTP console. There is also no light on the PoE port of the NVR when I plug in the camera.

Is there something that can be done to bring these cameras back to life?

Update (29/06/2024):
I guess I should update this since I was able to fix it and maybe this will help someone else.
  1. Dissemble the camera to reveal the circuit boards. There are two boards attached to each other and in the bottom most board (this board is stuck to the body of the camera so you have to pry it really hard but be careful about not breaking it) has a micro SD card in it.
  2. In the micro SD card formatted in FAT32 format, paste the firmware file but with as “digicap.bin” and insert the card into the slot.
  3. Assemble the camera and power it on.
  4. You should be able to see the camera in SADP now.
In my case, they had retained the previous config also.
 
Last edited:
B

bekars

n3wb
Joined
Jun 7, 2024
Messages
4
Reaction score
3
Location
Latvia
Hello all hik spec`s,

I purchased one DS-2CD2332-I camera from outlet, but it`s not working.
Started to search for some solutions and tried TFTP with each firmware staring from 5.2.0 - 5.4.5.
Update is successful, but after power cycle the camera goes in reboot loop, bellow terminal log with 5.2.0

Any ideas/suggestion`s?

Ctrl+u not stoping boot loader, also entered key`s are shown on screen like more than one symbol.


U-Boot 1.3.4-84026 (Jul 16 2014 - 16:51:43)

ARM Clock: 480MHz
DDR Clock: 336MHz
Hit Ctrl+u to stop autoboot: 2Hit Ctrl+u to stop autoboot: 1Hit Ctrl+u to stop autoboot: 0
|RCV UDP pack timeout|
Unknown command:null
nand booting ...
load kernel...
load ramdisk...
init started: BusyBox v1.19.3 (2014-07-11 11:25:54 CST)
starting pid 375, tty '': '/etc/init.d/rcS'
Starting udev: [ OK ]
starting pid 606, tty '': '/sbin/iptables -A INPUT -p tcp --dport 23 -j DROP'
starting pid 607, tty '': '/sbin/iptables -A INPUT -p tcp --dport 22 -j DROP'
starting pid 608, tty '': '/sbin/iptables -A INPUT -p tcp --dport 21 -j DROP'
starting pid 609, tty '': '/sbin/inetd -f -e /etc/inetd.conf'
starting pid 610, tty '': '-/bin/sh'


BusyBox v1.19.3 (2014-07-11 11:25:54 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

UBI device number 1, total 192 LEBs (24772608 bytes, 23.6 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi1_0.
Check dir /dav ok! (0)
UBI device number 3, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi3_0.
Check dir /davinci ok! (0)
UBI device number 4, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi4_0.
Check dir /config ok! (0)
Hit Ctrl+c to stop and exec /home/initrun.sh to continue
route: ioctl 0x890c failed: No such process
/dav
map_size = 0x300000
nr_item = 3
addr_offset = 0x0 filename = orccode.bin
addr_offset = 0x200000 filename = orcme.bin
addr_offset = 0x2a0000 filename = default_binary.bin
mmap returns 0x4032a000
loading ./orccode.bin...addr = 0x4032a000, size = 0x19f02d
loading ./orcme.bin...addr = 0x4052a000, size = 0x36374
loading ./default_binary.bin...addr = 0x405ca000, size = 0x40000
===============================
u_code version = 2013/10/24 3.0
===============================
ln: /dev/rtc: File exists
=====check_config start=====
===main db is ok===
start unix bus daemon
netprocess version: 1.0.13 [19:32:31-Jul 17 2014].
[01-14 14:23:23][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:23:23][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:23:23][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
[01-14 14:23:23][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
==================PPPoE is disable!!!
No need to recover kernel pri partition.
No need to recover ramdisk pri partition.
[01-14 14:23:24][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
[01-14 14:23:24][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:23:24][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:23:24][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
davinci receive cmd_query_davinci_param.
[01-14 14:23:25][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:25][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:25][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

========capture_mode_pal=17, capture_mode_ntsc=18===============.
powerLineFrequencyMode = 0
@@@motion PAL!!!!!!!!!!!!!!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:23:26][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:26][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:26][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
davinci receive cmd_query_davinci_param.
[01-14 14:23:27][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:27][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:27][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

get 0-0-0-0.000000-0-0-0
[01-14 14:23:27][pid:835][SYSINIT][ERROR]device not support RS485
[01-14 14:23:27][pid:835][HW_IF][ERROR]transfer_485_config_options error [options:57]
davinci receive cmd_query_davinci_param.
[01-14 14:23:27][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:27][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:27][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

IEfile uncompressed.
davinci receive cmd_query_davinci_param.
[01-14 14:23:28][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:28][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:28][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:29][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:29][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:29][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:30][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:30][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:30][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:31][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:31][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:31][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:32][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:32][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:32][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:init_dsp_lib() begin
<DSP> DBG:init_dsp_lib() end
[01-14 14:23:33][pid:835][DSP][ERROR][2]g_pdsp->audioTBShare.frameLen=80, g_pdsp->audioTBShare.totalFrame=128..
davinci receive cmd_query_davinci_param.
[01-14 14:23:33][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:33][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:33][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

mknod: /dev/snd/controlC0: File exists
mknod: /dev/snd/pcmC0D0c: File exists
mknod: /dev/snd/pcmC0D0p: File exists
[01-14 14:23:33][pid:835][HW_IF][ERROR]<read_fixed_noise_info_from_flash> (CFG_MAGIC != read.magicNumber(ffffffff)
davinci receive cmd_query_davinci_param.
[01-14 14:23:34][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:34][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:34][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:35][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:35][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:35][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:36][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:36][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:36][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:37][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:37][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:37][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

# davinci receive cmd_query_davinci_param.
[01-14 14:23:38][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:38][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:38][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:39][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:39][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:39][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:setup_dsp() begin
<DSP> DBG:init_cmem_module:cached_size=33030144(31M),noncached_size=6815744(6M)
init_cmem_module:CMEM_cmdline=insmod /dav/cmemk.ko phys_start=0xc6600000 phys_end=0xc8c00000 pools=1x33030144,1x6815744

davinci receive cmd_query_davinci_param.
[01-14 14:23:40][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:40][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:40][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

gdma Init Successful
b_fd=0,b_smd=1,b_scd=0
channel 1 is not 1 or 2<DSP> DBG:DSP start with Vout:Disabled,Audio:Disabled,VT:Disabled,MD:Enabled, vsync_guard:Enabled,vout_osd: Disabled, oversampling:Disabled, roi: Enabled, primacy: Disabled . hdr mode Disabled qr Disabled
<DSP> DBG:dsp_object.device_mode 0
<DSP> DBG:enc channel cnt 2, delay mode 0
Use CMEM buffer!
goto_idle done
pDspInitPara->VideoInitParam.capture_mode 125967385
find_video_mode sucusss!! mode 125967385 p_mode_table.vin_mode 30 vin_object.vin_fps 25.000000 vin w 1920 h 1080
set mode 30 type 21
vin_mode 2304*1296 vin_mode_temp 2304*1296 vin_mode_temp2 2304*1296#######pDspInitPara vout enable 0
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=0,maxRate(maxFps)=25.000000,fps=0x1
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=1.000000,clockStep=45000
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=0,fps=0x1,fpsFlg=0x1,frmPerSec=1,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=1,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=1,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=1,encode_type=1, (1920x1080), mirror type0, I inerval 50, bps 4014,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 1> in None MotionJPEG, skip!
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=2,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=2,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=2,encode_type=1, (352x288), mirror type0, I inerval 50, bps 501,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 2> in None MotionJPEG, skip!

overlay: start = 0x43c71000, total size = 0x100000 ( bytes)
b_rotate 0 overlay_level64 width 1920 height 1072
osd_width 1280 osd_scale_first 64 total 81920
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
init osd memory ok
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 1
chan 2, osd size 0 osd_size_changed 1
b_rotate 0 overlay_level16 width 1920 height 1072
osd_width 1280 osd_scale_first 16 total 20480
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=0,flgOsd=0x1, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=1,flgOsd=0x3, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
davinci receive cmd_query_davinci_param.
[01-14 14:23:41][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:41][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:41][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=2,flgOsd=0x7, bStart=1
init osd success
<VidThrd> DBG:setup_video_input begin
<VidThrd> ERR:please load source driver!
<VidThrd> ERR:set video source failed!
<DSP> ERR:setup_dsp:setup_video_input
[01-14 14:23:41][pid:835][DSP][ERROR]DSP 初始化失败...
[01-14 14:23:41][pid:835][SYSINIT][ERROR]hwif_dsp_init error force sys reboot,ret=-12!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:23:42][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:42][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:42][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 1

U-Boot 1.3.4-84026 (Jul 16 2014 - 16:51:43)

ARM Clock: 480MHz
DDR Clock: 336MHz
Hit Ctrl+u to stop autoboot: 2Hit Ctrl+u to stop autoboot: 1Hit Ctrl+u to stop autoboot: 0
|RCV UDP pack timeout|
Unknown command:null
nand booting ...
load kernel...
load ramdisk...
init started: BusyBox v1.19.3 (2014-07-11 11:25:54 CST)
starting pid 375, tty '': '/etc/init.d/rcS'
Starting udev: [ OK ]
starting pid 606, tty '': '/sbin/iptables -A INPUT -p tcp --dport 23 -j DROP'
starting pid 607, tty '': '/sbin/iptables -A INPUT -p tcp --dport 22 -j DROP'
starting pid 608, tty '': '/sbin/iptables -A INPUT -p tcp --dport 21 -j DROP'
starting pid 609, tty '': '/sbin/inetd -f -e /etc/inetd.conf'
starting pid 610, tty '': '-/bin/sh'


BusyBox v1.19.3 (2014-07-11 11:25:54 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

UBI device number 1, total 192 LEBs (24772608 bytes, 23.6 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi1_0.
Check dir /dav ok! (0)
UBI device number 3, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi3_0.
Check dir /davinci ok! (0)
UBI device number 4, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi4_0.
Check dir /config ok! (0)
Hit Ctrl+c to stop and exec /home/initrun.sh to continue
route: ioctl 0x890c failed: No such process
/dav
map_size = 0x300000
nr_item = 3
addr_offset = 0x0 filename = orccode.bin
addr_offset = 0x200000 filename = orcme.bin
addr_offset = 0x2a0000 filename = default_binary.bin
mmap returns 0x402e6000
loading ./orccode.bin...addr = 0x402e6000, size = 0x19f02d
loading ./orcme.bin...addr = 0x404e6000, size = 0x36374
loading ./default_binary.bin...addr = 0x40586000, size = 0x40000
===============================
u_code version = 2013/10/24 3.0
===============================
ln: /dev/rtc: File exists
=====check_config start=====
===main db is ok===
start unix bus daemon
netprocess version: 1.0.13 [19:32:31-Jul 17 2014].
[01-14 14:24:08][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:24:08][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:24:08][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
[01-14 14:24:08][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
==================PPPoE is disable!!!
No need to recover kernel pri partition.
No need to recover ramdisk pri partition.
[01-14 14:24:09][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
[01-14 14:24:09][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:24:09][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:24:09][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
davinci receive cmd_query_davinci_param.
[01-14 14:24:10][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:10][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:10][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

========capture_mode_pal=17, capture_mode_ntsc=18===============.
powerLineFrequencyMode = 0
@@@motion PAL!!!!!!!!!!!!!!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:24:11][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:11][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:11][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get 0-0-0-0.000000-0-0-0
davinci receive cmd_query_davinci_param.
[01-14 14:24:12][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:12][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:12][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

[01-14 14:24:12][pid:835][SYSINIT][ERROR]device not support RS485
[01-14 14:24:12][pid:835][HW_IF][ERROR]transfer_485_config_options error [options:57]
davinci receive cmd_query_davinci_param.
[01-14 14:24:12][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:12][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:12][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

IEfile uncompressed.
davinci receive cmd_query_davinci_param.
[01-14 14:24:13][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:13][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:13][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:14][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:14][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:14][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:15][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:15][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:15][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:16][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:16][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:16][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:17][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:17][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:17][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:init_dsp_lib() begin
<DSP> DBG:init_dsp_lib() end
[01-14 14:24:18][pid:835][DSP][ERROR][2]g_pdsp->audioTBShare.frameLen=80, g_pdsp->audioTBShare.totalFrame=128..
mknod: /dev/snd/controlC0: File exists
mknod: /dev/snd/pcmC0D0c: File exists
mknod: /dev/snd/pcmC0D0p: File exists
[01-14 14:24:18][pid:835][HW_IF][ERROR]<read_fixed_noise_info_from_flash> (CFG_MAGIC != read.magicNumber(ffffffff)
davinci receive cmd_query_davinci_param.
[01-14 14:24:18][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:18][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:18][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:19][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:19][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:19][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:20][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:20][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:20][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:21][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:21][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:21][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:22][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:22][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:22][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

# davinci receive cmd_query_davinci_param.
[01-14 14:24:23][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:23][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:23][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:24][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:24][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:24][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:setup_dsp() begin
<DSP> DBG:init_cmem_module:cached_size=33030144(31M),noncached_size=6815744(6M)
init_cmem_module:CMEM_cmdline=insmod /dav/cmemk.ko phys_start=0xc6600000 phys_end=0xc8c00000 pools=1x33030144,1x6815744

davinci receive cmd_query_davinci_param.
[01-14 14:24:25][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:25][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:25][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

gdma Init Successful
b_fd=0,b_smd=1,b_scd=0
channel 1 is not 1 or 2<DSP> DBG:DSP start with Vout:Disabled,Audio:Disabled,VT:Disabled,MD:Enabled, vsync_guard:Enabled,vout_osd: Disabled, oversampling:Disabled, roi: Enabled, primacy: Disabled . hdr mode Disabled qr Disabled
<DSP> DBG:dsp_object.device_mode 0
<DSP> DBG:enc channel cnt 2, delay mode 0
Use CMEM buffer!
goto_idle done
pDspInitPara->VideoInitParam.capture_mode 125967385
find_video_mode sucusss!! mode 125967385 p_mode_table.vin_mode 30 vin_object.vin_fps 25.000000 vin w 1920 h 1080
set mode 30 type 21
vin_mode 2304*1296 vin_mode_temp 2304*1296 vin_mode_temp2 2304*1296#######pDspInitPara vout enable 0
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=0,maxRate(maxFps)=25.000000,fps=0x1
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=1.000000,clockStep=45000
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=0,fps=0x1,fpsFlg=0x1,frmPerSec=1,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=1,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=1,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=1,encode_type=1, (1920x1080), mirror type0, I inerval 50, bps 4014,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 1> in None MotionJPEG, skip!
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=2,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=2,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=2,encode_type=1, (352x288), mirror type0, I inerval 50, bps 501,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 2> in None MotionJPEG, skip!

overlay: start = 0x43ceb000, total size = 0x100000 ( bytes)
b_rotate 0 overlay_level64 width 1920 height 1072
osd_width 1280 osd_scale_first 64 total 81920
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
init osd memory ok
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 1
chan 2, osd size 0 osd_size_changed 1
b_rotate 0 overlay_level16 width 1920 height 1072
osd_width 1280 osd_scale_first 16 total 20480
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=0,flgOsd=0x1, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=1,flgOsd=0x3, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=2,flgOsd=0x7, bStart=1
init osd success
<VidThrd> DBG:setup_video_input begin
<VidThrd> ERR:please load source driver!
<VidThrd> ERR:set video source failed!
<DSP> ERR:setup_dsp:setup_video_input
[01-14 14:24:26][pid:835][DSP][ERROR]DSP 初始化失败...
[01-14 14:24:26][pid:835][SYSINIT][ERROR]hwif_dsp_init error force sys reboot,ret=-12!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:24:26][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:26][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:26][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:27][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:27][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:27][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param



U-Boot 1.3.4-84026 (Jul 16 2014 - 16:51:43)

ARM Clock: 480MHz
DDR Clock: 336MHz
Hit Ctrl+u to stop autoboot: 2Hit Ctrl+u to stop autoboot: 1Hit Ctrl+u to stop autoboot: 0
|RCV UDP pack timeout|
Unknown command:null
nand booting ...
load kernel...
load ramdisk...
init started: BusyBox v1.19.3 (2014-07-11 11:25:54 CST)
starting pid 375, tty '': '/etc/init.d/rcS'
Starting udev: [ OK ]
starting pid 606, tty '': '/sbin/iptables -A INPUT -p tcp --dport 23 -j DROP'
starting pid 607, tty '': '/sbin/iptables -A INPUT -p tcp --dport 22 -j DROP'
starting pid 608, tty '': '/sbin/iptables -A INPUT -p tcp --dport 21 -j DROP'
starting pid 609, tty '': '/sbin/inetd -f -e /etc/inetd.conf'
starting pid 610, tty '': '-/bin/sh'


BusyBox v1.19.3 (2014-07-11 11:25:54 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

UBI device number 1, total 192 LEBs (24772608 bytes, 23.6 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi1_0.
Check dir /dav ok! (0)
UBI device number 3, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi3_0.
Check dir /davinci ok! (0)
UBI device number 4, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi4_0.
Check dir /config ok! (0)
Hit Ctrl+c to stop and exec /home/initrun.sh to continue
route: ioctl 0x890c failed: No such process
/dav
map_size = 0x300000
nr_item = 3
addr_offset = 0x0 filename = orccode.bin
addr_offset = 0x200000 filename = orcme.bin
addr_offset = 0x2a0000 filename = default_binary.bin
mmap returns 0x402ff000
loading ./orccode.bin...addr = 0x402ff000, size = 0x19f02d
loading ./orcme.bin...addr = 0x404ff000, size = 0x36374
loading ./default_binary.bin...addr = 0x4059f000, size = 0x40000
===============================
u_code version = 2013/10/24 3.0
===============================
ln: /dev/rtc: File exists
=====check_config start=====
===main db is ok===
start unix bus daemon
netprocess version: 1.0.13 [19:32:31-Jul 17 2014].
[01-14 14:24:53][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:24:53][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:24:53][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
[01-14 14:24:53][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
==================PPPoE is disable!!!
No need to recover kernel pri partition.
No need to recover ramdisk pri partition.
davinci receive cmd_query_davinci_param.
[01-14 14:24:54][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:54][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:54][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:55][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:55][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:55][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

========capture_mode_pal=17, capture_mode_ntsc=18===============.
powerLineFrequencyMode = 0
@@@motion PAL!!!!!!!!!!!!!!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:24:56][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:56][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:56][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get 0-0-0-0.000000-0-0-0
davinci receive cmd_query_davinci_param.
[01-14 14:24:57][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:57][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:57][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

[01-14 14:24:57][pid:835][SYSINIT][ERROR]device not support RS485
[01-14 14:24:57][pid:835][HW_IF][ERROR]transfer_485_config_options error [options:57]
davinci receive cmd_query_davinci_param.
[01-14 14:24:57][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:57][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:57][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

IEfile uncompressed.
davinci receive cmd_query_davinci_param.
[01-14 14:24:58][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:58][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:58][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:59][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:59][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:59][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:00][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:00][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:00][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:01][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:01][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:01][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:02][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:02][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:02][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:init_dsp_lib() begin
<DSP> DBG:init_dsp_lib() end
[01-14 14:25:03][pid:835][DSP][ERROR][2]g_pdsp->audioTBShare.frameLen=80, g_pdsp->audioTBShare.totalFrame=128..
mknod: /dev/snd/controlC0: File exists
mknod: /dev/snd/pcmC0D0c: File exists
mknod: /dev/snd/pcmC0D0p: File exists
[01-14 14:25:03][pid:835][HW_IF][ERROR]<read_fixed_noise_info_from_flash> (CFG_MAGIC != read.magicNumber(ffffffff)
davinci receive cmd_query_davinci_param.
[01-14 14:25:03][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:03][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:03][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:04][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:04][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:04][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:05][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:05][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:05][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:06][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:06][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:06][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:07][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:07][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:07][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

# davinci receive cmd_query_davinci_param.
[01-14 14:25:08][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:08][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:08][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:09][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:09][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:09][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:setup_dsp() begin
<DSP> DBG:init_cmem_module:cached_size=33030144(31M),noncached_size=6815744(6M)
init_cmem_module:CMEM_cmdline=insmod /dav/cmemk.ko phys_start=0xc6600000 phys_end=0xc8c00000 pools=1x33030144,1x6815744

davinci receive cmd_query_davinci_param.
[01-14 14:25:10][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:10][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:10][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

gdma Init Successful
b_fd=0,b_smd=1,b_scd=0
channel 1 is not 1 or 2<DSP> DBG:DSP start with Vout:Disabled,Audio:Disabled,VT:Disabled,MD:Enabled, vsync_guard:Enabled,vout_osd: Disabled, oversampling:Disabled, roi: Enabled, primacy: Disabled . hdr mode Disabled qr Disabled
<DSP> DBG:dsp_object.device_mode 0
<DSP> DBG:enc channel cnt 2, delay mode 0
Use CMEM buffer!
goto_idle done
pDspInitPara->VideoInitParam.capture_mode 125967385
find_video_mode sucusss!! mode 125967385 p_mode_table.vin_mode 30 vin_object.vin_fps 25.000000 vin w 1920 h 1080
set mode 30 type 21
vin_mode 2304*1296 vin_mode_temp 2304*1296 vin_mode_temp2 2304*1296#######pDspInitPara vout enable 0
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=0,maxRate(maxFps)=25.000000,fps=0x1
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=1.000000,clockStep=45000
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=0,fps=0x1,fpsFlg=0x1,frmPerSec=1,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=1,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=1,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=1,encode_type=1, (1920x1080), mirror type0, I inerval 50, bps 4014,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 1> in None MotionJPEG, skip!
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=2,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=2,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=2,encode_type=1, (352x288), mirror type0, I inerval 50, bps 501,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 2> in None MotionJPEG, skip!

overlay: start = 0x43a6b000, total size = 0x100000 ( bytes)
b_rotate 0 overlay_level64 width 1920 height 1072
osd_width 1280 osd_scale_first 64 total 81920
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
init osd memory ok
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 1
chan 2, osd size 0 osd_size_changed 1
b_rotate 0 overlay_level16 width 1920 height 1072
osd_width 1280 osd_scale_first 16 total 20480
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=0,flgOsd=0x1, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=1,flgOsd=0x3, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=2,flgOsd=0x7, bStart=1
init osd success
<VidThrd> DBG:setup_video_input begin
<VidThrd> ERR:please load source driver!
<VidThrd> ERR:set video source failed!
<DSP> ERR:setup_dsp:setup_video_input
[01-14 14:25:11][pid:835][DSP][ERROR]DSP 初始化失败...
[01-14 14:25:11][pid:835][SYSINIT][ERROR]hwif_dsp_init error force sys reboot,ret=-12!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:25:11][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:11][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:11][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:12][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:12][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:12][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param



U-Boot 1.3.4-84026 (Jul 16 2014 - 16:51:43)

ARM Clock: 480MHz
DDR Clock: 336MHz
Hit Ctrl+u to stop autoboot: 2Hit Ctrl+u to stop autoboot: 1Hit Ctrl+u to stop autoboot: 0
|RCV UDP pack timeout|
Unknown command:null
nand booting ...
load kernel...
load ramdisk...
init started: BusyBox v1.19.3 (2014-07-11 11:25:54 CST)
starting pid 375, tty '': '/etc/init.d/rcS'
Starting udev: [ OK ]
starting pid 606, tty '': '/sbin/iptables -A INPUT -p tcp --dport 23 -j DROP'
starting pid 607, tty '': '/sbin/iptables -A INPUT -p tcp --dport 22 -j DROP'
starting pid 608, tty '': '/sbin/iptables -A INPUT -p tcp --dport 21 -j DROP'
starting pid 609, tty '': '/sbin/inetd -f -e /etc/inetd.conf'
starting pid 610, tty '': '-/bin/sh'


BusyBox v1.19.3 (2014-07-11 11:25:54 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

UBI device number 1, total 192 LEBs (24772608 bytes, 23.6 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi1_0.
Check dir /dav ok! (0)
UBI device number 3, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi3_0.
Check dir /davinci ok! (0)
UBI device number 4, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi4_0.
Check dir /config ok! (0)
Hit Ctrl+c to stop and exec /home/initrun.sh to continue
route: ioctl 0x890c failed: No such process
/dav
map_size = 0x300000
nr_item = 3
addr_offset = 0x0 filename = orccode.bin
addr_offset = 0x200000 filename = orcme.bin
addr_offset = 0x2a0000 filename = default_binary.bin
mmap returns 0x402e8000
loading ./orccode.bin...addr = 0x402e8000, size = 0x19f02d
loading ./orcme.bin...addr = 0x404e8000, size = 0x36374
loading ./default_binary.bin...addr = 0x40588000, size = 0x40000
===============================
u_code version = 2013/10/24 3.0
===============================
ln: /dev/rtc: File exists
=====check_config start=====
===main db is ok===
start unix bus daemon
netprocess version: 1.0.13 [19:32:31-Jul 17 2014].
[01-14 14:25:39][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:25:39][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:25:39][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
[01-14 14:25:39][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
==================PPPoE is disable!!!
No need to recover kernel pri partition.
No need to recover ramdisk pri partition.
davinci receive cmd_query_davinci_param.
[01-14 14:25:40][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:40][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:40][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

========capture_mode_pal=17, capture_mode_ntsc=18===============.
powerLineFrequencyMode = 0
davinci receive cmd_query_davinci_param.
[01-14 14:25:41][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:41][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:41][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

@@@motion PAL!!!!!!!!!!!!!!!!!
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
davinci receive cmd_query_davinci_param.
[01-14 14:25:42][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:42][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:42][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

get 0-0-0-0.000000-0-0-0
[01-14 14:25:43][pid:835][SYSINIT][ERROR]device not support RS485
[01-14 14:25:43][pid:835][HW_IF][ERROR]transfer_485_config_options error [options:57]
davinci receive cmd_query_davinci_param.
[01-14 14:25:43][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:43][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:43][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:42][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:42][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:42][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

IEfile uncompressed.
davinci receive cmd_query_davinci_param.
[01-14 14:25:43][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:43][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:43][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:44][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:44][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:44][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:45][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:45][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:45][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:46][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:46][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:46][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:47][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:47][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:47][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:init_dsp_lib() begin
<DSP> DBG:init_dsp_lib() end
[01-14 14:25:48][pid:835][DSP][ERROR][2]g_pdsp->audioTBShare.frameLen=80, g_pdsp->audioTBShare.totalFrame=128..
mknod: /dev/snd/controlC0: File exists
mknod: /dev/snd/pcmC0D0c: File exists
mknod: /dev/snd/pcmC0D0p: File exists
[01-14 14:25:48][pid:835][HW_IF][ERROR]<read_fixed_noise_info_from_flash> (CFG_MAGIC != read.magicNumber(ffffffff)
davinci receive cmd_query_davinci_param.
[01-14 14:25:49][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:49][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:49][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:50][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:50][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:50][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:51][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:51][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:51][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:52][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:52][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:52][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:53][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:53][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:53][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

# davinci receive cmd_query_davinci_param.
[01-14 14:25:54][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:54][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:54][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:setup_dsp() begin
<DSP> DBG:init_cmem_module:cached_size=33030144(31M),noncached_size=6815744(6M)
init_cmem_module:CMEM_cmdline=insmod /dav/cmemk.ko phys_start=0xc6600000 phys_end=0xc8c00000 pools=1x33030144,1x6815744

davinci receive cmd_query_davinci_param.
[01-14 14:25:55][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:55][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:55][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:56][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:56][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:56][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

gdma Init Successful
b_fd=0,b_smd=1,b_scd=0
channel 1 is not 1 or 2<DSP> DBG:DSP start with Vout:Disabled,Audio:Disabled,VT:Disabled,MD:Enabled, vsync_guard:Enabled,vout_osd: Disabled, oversampling:Disabled, roi: Enabled, primacy: Disabled . hdr mode Disabled qr Disabled
<DSP> DBG:dsp_object.device_mode 0
<DSP> DBG:enc channel cnt 2, delay mode 0
Use CMEM buffer!
goto_idle done
pDspInitPara->VideoInitParam.capture_mode 125967385
find_video_mode sucusss!! mode 125967385 p_mode_table.vin_mode 30 vin_object.vin_fps 25.000000 vin w 1920 h 1080
set mode 30 type 21
vin_mode 2304*1296 vin_mode_temp 2304*1296 vin_mode_temp2 2304*1296#######pDspInitPara vout enable 0
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=0,maxRate(maxFps)=25.000000,fps=0x1
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=1.000000,clockStep=45000
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=0,fps=0x1,fpsFlg=0x1,frmPerSec=1,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=1,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=1,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=1,encode_type=1, (1920x1080), mirror type0, I inerval 50, bps 4014,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 1> in None MotionJPEG, skip!
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=2,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=2,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=2,encode_type=1, (352x288), mirror type0, I inerval 50, bps 501,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 2> in None MotionJPEG, skip!

overlay: start = 0x43bbb000, total size = 0x100000 ( bytes)
b_rotate 0 overlay_level64 width 1920 height 1072
osd_width 1280 osd_scale_first 64 total 81920
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
init osd memory ok
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 1
chan 2, osd size 0 osd_size_changed 1
b_rotate 0 overlay_level16 width 1920 height 1072
osd_width 1280 osd_scale_first 16 total 20480
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=0,flgOsd=0x1, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=1,flgOsd=0x3, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=2,flgOsd=0x7, bStart=1
init osd success
<VidThrd> DBG:setup_video_input begin
<VidThrd> ERR:please load source driver!
<VidThrd> ERR:set video source failed!
<DSP> ERR:setup_dsp:setup_video_input
[01-14 14:25:56][pid:835][DSP][ERROR]DSP 初始化失败...
[01-14 14:25:56][pid:835][SYSINIT][ERROR]hwif_dsp_init error force sys reboot,ret=-12!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:25:57][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:57][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:57][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:58][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:58][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:58][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param



U-Boot 1.3.4-84026 (Jul 16 2014 - 16:51:43)

ARM Clock: 480MHz
DDR Clock: 336MHz
Hit Ctrl+u to stop autoboot: 2Hit Ctrl+u to stop autoboot: 1Hit Ctrl+u to stop autoboot: 0
|RCV UDP pack timeout|
Unknown command:null
nand booting ...
load kernel...
load ramdisk...
init started: BusyBox v1.19.3 (2014-07-11 11:25:54 CST)
starting pid 375, tty '': '/etc/init.d/rcS'
Starting udev: [ OK ]
starting pid 606, tty '': '/sbin/iptables -A INPUT -p tcp --dport 23 -j DROP'
starting pid 607, tty '': '/sbin/iptables -A INPUT -p tcp --dport 22 -j DROP'
starting pid 608, tty '': '/sbin/iptables -A INPUT -p tcp --dport 21 -j DROP'
starting pid 609, tty '': '/sbin/inetd -f -e /etc/inetd.conf'
starting pid 610, tty '': '-/bin/sh'


BusyBox v1.19.3 (2014-07-11 11:25:54 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

UBI device number 1, total 192 LEBs (24772608 bytes, 23.6 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi1_0.
Check dir /dav ok! (0)
UBI device number 3, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi3_0.
Check dir /davinci ok! (0)
UBI device number 4, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi4_0.
Check dir /config ok! (0)
Hit Ctrl+c to stop and exec /home/initrun.sh to continue
route: ioctl 0x890c failed: No such process
/dav
map_size = 0x300000
nr_item = 3
addr_offset = 0x0 filename = orccode.bin
addr_offset = 0x200000 filename = orcme.bin
addr_offset = 0x2a0000 filename = default_binary.bin
mmap returns 0x40314000
loading ./orccode.bin...addr = 0x40314000, size = 0x19f02d
loading ./orcme.bin...addr = 0x40514000, size = 0x36374
loading ./default_binary.bin...addr = 0x405b4000, size = 0x40000
===============================
u_code version = 2013/10/24 3.0
===============================
ln: /dev/rtc: File exists
=====check_config start=====
===main db is ok===
start unix bus daemon
netprocess version: 1.0.13 [19:32:31-Jul 17 2014].
[01-14 14:26:23][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:26:23][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:26:23][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
[01-14 14:26:23][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
==================PPPoE is disable!!!
No need to recover kernel pri partition.
No need to recover ramdisk pri partition.
[01-14 14:26:24][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
[01-14 14:26:24][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:26:24][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:26:24][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
davinci receive cmd_query_davinci_param.
[01-14 14:26:25][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:25][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:25][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

========capture_mode_pal=17, capture_mode_ntsc=18===============.
powerLineFrequencyMode = 0
@@@motion PAL!!!!!!!!!!!!!!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:26:26][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:26][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:26][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get 0-0-0-0.000000-0-0-0
davinci receive cmd_query_davinci_param.
[01-14 14:26:27][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:27][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:27][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

[01-14 14:26:27][pid:835][SYSINIT][ERROR]device not support RS485
[01-14 14:26:27][pid:835][HW_IF][ERROR]transfer_485_config_options error [options:57]
davinci receive cmd_query_davinci_param.
[01-14 14:26:27][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:27][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:27][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

IEfile uncompressed.
davinci receive cmd_query_davinci_param.
[01-14 14:26:28][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:28][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:28][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:29][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:29][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:29][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:30][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:30][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:30][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:31][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:31][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:31][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:32][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:32][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:32][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:init_dsp_lib() begin
<DSP> DBG:init_dsp_lib() end
[01-14 14:26:33][pid:835][DSP][ERROR][2]g_pdsp->audioTBShare.frameLen=80, g_pdsp->audioTBShare.totalFrame=128..
mknod: /dev/snd/controlC0: File exists
mknod: /dev/snd/pcmC0D0c: File exists
mknod: /dev/snd/pcmC0D0p: File exists
[01-14 14:26:33][pid:835][HW_IF][ERROR]<read_fixed_noise_info_from_flash> (CFG_MAGIC != read.magicNumber(ffffffff)
davinci receive cmd_query_davinci_param.
[01-14 14:26:33][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:33][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:33][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:34][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:34][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:34][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:35][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:35][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:35][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:36][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:36][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:36][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:37][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:37][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:37][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

# davinci receive cmd_query_davinci_param.
[01-14 14:26:38][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:38][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:38][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:39][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:39][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:39][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:setup_dsp() begin
<DSP> DBG:init_cmem_module:cached_size=33030144(31M),noncached_size=6815744(6M)
init_cmem_module:CMEM_cmdline=insmod /dav/cmemk.ko phys_start=0xc6600000 phys_end=0xc8c00000 pools=1x33030144,1x6815744

davinci receive cmd_query_davinci_param.
[01-14 14:26:40][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:40][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:40][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

gdma Init Successful
b_fd=0,b_smd=1,b_scd=0
channel 1 is not 1 or 2<DSP> DBG:DSP start with Vout:Disabled,Audio:Disabled,VT:Disabled,MD:Enabled, vsync_guard:Enabled,vout_osd: Disabled, oversampling:Disabled, roi: Enabled, primacy: Disabled . hdr mode Disabled qr Disabled
<DSP> DBG:dsp_object.device_mode 0
<DSP> DBG:enc channel cnt 2, delay mode 0
Use CMEM buffer!
goto_idle done
pDspInitPara->VideoInitParam.capture_mode 125967385
find_video_mode sucusss!! mode 125967385 p_mode_table.vin_mode 30 vin_object.vin_fps 25.000000 vin w 1920 h 1080
set mode 30 type 21
vin_mode 2304*1296 vin_mode_temp 2304*1296 vin_mode_temp2 2304*1296#######pDspInitPara vout enable 0
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=0,maxRate(maxFps)=25.000000,fps=0x1
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=1.000000,clockStep=45000
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=0,fps=0x1,fpsFlg=0x1,frmPerSec=1,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=1,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=1,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=1,encode_type=1, (1920x1080), mirror type0, I inerval 50, bps 4014,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 1> in None MotionJPEG, skip!
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=2,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=2,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=2,encode_type=1, (352x288), mirror type0, I inerval 50, bps 501,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 2> in None MotionJPEG, skip!

overlay: start = 0x43bd8000, total size = 0x100000 ( bytes)
b_rotate 0 overlay_level64 width 1920 height 1072
osd_width 1280 osd_scale_first 64 total 81920
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
init osd memory ok
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 1
chan 2, osd size 0 osd_size_changed 1
b_rotate 0 overlay_level16 width 1920 height 1072
osd_width 1280 osd_scale_first 16 total 20480
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=0,flgOsd=0x1, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=1,flgOsd=0x3, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=2,flgOsd=0x7, bStart=1
init osd success
<VidThrd> DBG:setup_video_input begin
<VidThrd> ERR:please load source driver!
<VidThrd> ERR:set video source failed!
<DSP> ERR:setup_dsp:setup_video_input
[01-14 14:26:41][pid:835][DSP][ERROR]DSP 初始化失败...
[01-14 14:26:41][pid:835][SYSINIT][ERROR]hwif_dsp_init error force sys reboot,ret=-12!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:26:41][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:41][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:41][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:42][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:42][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:42][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

Click to expand...
 
B

bekars

n3wb
Joined
Jun 7, 2024
Messages
4
Reaction score
3
Location
Latvia
bekars said:
Hello all hik spec`s,

I purchased one DS-2CD2332-I camera from outlet, but it`s not working.
Started to search for some solutions and tried TFTP with each firmware staring from 5.2.0 - 5.4.5.
Update is successful, but after power cycle the camera goes in reboot loop, bellow terminal log with 5.2.0

Any ideas/suggestion`s?

Ctrl+u not stoping boot loader, also entered key`s are shown on screen like more than one symbol.
Click to expand...
found a solution based on error "hwif_dsp_init error force sys reboot,ret=-12 ", thr suggestion was to disconnect and reconnect cameras flat cable.
My camera is working now :)
 
alastairstevenson

alastairstevenson

Staff member
Joined
Oct 28, 2014
Messages
15,979
Reaction score
6,827
Location
Scotland
bekars said:
Ctrl+u not stoping boot loader, also entered key`s are shown on screen like more than one symbol.
Click to expand...
I know you've fixed the problem by re-seating the ribbon cable to the sensor module - but maybe worth commenting for future use :

If you can't stop the bootloader, and what you type does not show correctly, it suggests the serial TTL connection to the camera is not wired correctly.
Is it wired like this example (camera connector is the same as the NVR)?

Hikvision NVR DS-7804N-E1/4P Bricked

Hello, i have NVR DS-7804N-E1/4P bricked when i flash wrong firmware DS-7604NI for it. So now it only boot to Logo then bip bip and auto restart. I tried flash TFTP very many time by set IP of my PC to 192.0.0.128 / subnet 255.255.255.0 and turn firewall is off. But no thing flashable although i...
ipcamtalk.com ipcamtalk.com
 
B

bekars

n3wb
Joined
Jun 7, 2024
Messages
4
Reaction score
3
Location
Latvia
alastairstevenson said:
I know you've fixed the problem by re-seating the ribbon cable to the sensor module - but maybe worth commenting for future use :

If you can't stop the bootloader, and what you type does not show correctly, it suggests the serial TTL connection to the camera is not wired correctly.
Is it wired like this example (camera connector is the same as the NVR)?

Hikvision NVR DS-7804N-E1/4P Bricked

Hello, i have NVR DS-7804N-E1/4P bricked when i flash wrong firmware DS-7604NI for it. So now it only boot to Logo then bip bip and auto restart. I tried flash TFTP very many time by set IP of my PC to 192.0.0.128 / subnet 255.255.255.0 and turn firewall is off. But no thing flashable although i...
ipcamtalk.com ipcamtalk.com
Click to expand...
According to you pinout example an all others I found, I could not get any response in putty.

But only with this I can get cameras activity on putty
TTL RX - PIN3 Camera
TX - PIN 1
GND - PIN 2

For example when I press key A in putty I receive back A&
 
B

bekars

n3wb
Joined
Jun 7, 2024
Messages
4
Reaction score
3
Location
Latvia
alastairstevenson said:
What happens when you swap the connections to 1 and 2 around?
Click to expand...
Nothing in putty, complete silence - tried camera power cycle, restart putty session, PC with WIN 11 also XP
I have 3 USB TTL converts and wit all of them I get such behavior.
I also tried with other camera and got the same behavior.

The only thing which is not double checked is cable between TTL and camera, I assembled the ZH-4 connecter with the contact`s on wires by myself - it was purchased as separated components available local shop.
Checked it with multimeter, no shortcut between pin wires... .
Will order some "ready" pack from amazon.

BUT the overall main goal was reached why I purchased this camera - I bought couple NVR`s DS-7716NI-I4/16P(B) from auction and of course password was not known :D
Password extraction via PoE works like a charm.
NVR`s booloaders are on last fw where HKVS $ does not react on any command - this has direct RS232 connection with null modem cable.
 
You must log in or register to reply here.
Top