R0 / DS-2CD2x32 BrickfixV2 brick recovery and full upgrade tool - enhanced.

I hope someone can help me with this.

I have a few Hikvision cameras (DS-2XMG222G0-ID(AE)) that I tried to upgrade the firmware using Postman. The upgrade was successful many times with the response being “Reboot Required” and I called another API to perform the reboot. I was flashing the same firmware multiple times to test the API. The version was V1.3.6.

However, once, I got a connection reset error and the camera just died and did not turn on. The next day, another camera died and wouldn't power on at all. These cameras had a static IP on the network and were plugged into an NVR (DS-MP7608HN) with it also being connected to the network. Today, two more cameras died while upgrading. I didn't get any response, just a “Connection Reset. Unexpected end of stream” in the logs.

I tried to do the method listed here, but I don't get any response on the TFTP at all. I also followed Wendell's step and used Scott's script but no luck at all. Furthermore, I am not able to detect the cameras at all. Nothing happens on the TFTP console. There is also no light on the PoE port of the NVR when I plug in the camera.

Is there something that can be done to bring these cameras back to life?

Update (29/06/2024):
I guess I should update this since I was able to fix it and maybe this will help someone else.
  1. Dissemble the camera to reveal the circuit boards. There are two boards attached to each other and in the bottom most board (this board is stuck to the body of the camera so you have to pry it really hard but be careful about not breaking it) has a micro SD card in it.
  2. In the micro SD card formatted in FAT32 format, paste the firmware file but with as “digicap.bin” and insert the card into the slot.
  3. Assemble the camera and power it on.
  4. You should be able to see the camera in SADP now.
In my case, they had retained the previous config also.
 
Last edited:
Hello all hik spec`s,

I purchased one DS-2CD2332-I camera from outlet, but it`s not working.
Started to search for some solutions and tried TFTP with each firmware staring from 5.2.0 - 5.4.5.
Update is successful, but after power cycle the camera goes in reboot loop, bellow terminal log with 5.2.0

Any ideas/suggestion`s?

Ctrl+u not stoping boot loader, also entered key`s are shown on screen like more than one symbol.


U-Boot 1.3.4-84026 (Jul 16 2014 - 16:51:43)

ARM Clock: 480MHz
DDR Clock: 336MHz
Hit Ctrl+u to stop autoboot: 2Hit Ctrl+u to stop autoboot: 1Hit Ctrl+u to stop autoboot: 0
|RCV UDP pack timeout|
Unknown command:null
nand booting ...
load kernel...
load ramdisk...
init started: BusyBox v1.19.3 (2014-07-11 11:25:54 CST)
starting pid 375, tty '': '/etc/init.d/rcS'
Starting udev: [ OK ]
starting pid 606, tty '': '/sbin/iptables -A INPUT -p tcp --dport 23 -j DROP'
starting pid 607, tty '': '/sbin/iptables -A INPUT -p tcp --dport 22 -j DROP'
starting pid 608, tty '': '/sbin/iptables -A INPUT -p tcp --dport 21 -j DROP'
starting pid 609, tty '': '/sbin/inetd -f -e /etc/inetd.conf'
starting pid 610, tty '': '-/bin/sh'


BusyBox v1.19.3 (2014-07-11 11:25:54 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

UBI device number 1, total 192 LEBs (24772608 bytes, 23.6 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi1_0.
Check dir /dav ok! (0)
UBI device number 3, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi3_0.
Check dir /davinci ok! (0)
UBI device number 4, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi4_0.
Check dir /config ok! (0)
Hit Ctrl+c to stop and exec /home/initrun.sh to continue
route: ioctl 0x890c failed: No such process
/dav
map_size = 0x300000
nr_item = 3
addr_offset = 0x0 filename = orccode.bin
addr_offset = 0x200000 filename = orcme.bin
addr_offset = 0x2a0000 filename = default_binary.bin
mmap returns 0x4032a000
loading ./orccode.bin...addr = 0x4032a000, size = 0x19f02d
loading ./orcme.bin...addr = 0x4052a000, size = 0x36374
loading ./default_binary.bin...addr = 0x405ca000, size = 0x40000
===============================
u_code version = 2013/10/24 3.0
===============================
ln: /dev/rtc: File exists
=====check_config start=====
===main db is ok===
start unix bus daemon
netprocess version: 1.0.13 [19:32:31-Jul 17 2014].
[01-14 14:23:23][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:23:23][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:23:23][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
[01-14 14:23:23][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
==================PPPoE is disable!!!
No need to recover kernel pri partition.
No need to recover ramdisk pri partition.
[01-14 14:23:24][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
[01-14 14:23:24][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:23:24][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:23:24][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
davinci receive cmd_query_davinci_param.
[01-14 14:23:25][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:25][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:25][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

========capture_mode_pal=17, capture_mode_ntsc=18===============.
powerLineFrequencyMode = 0
@@@motion PAL!!!!!!!!!!!!!!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:23:26][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:26][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:26][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
davinci receive cmd_query_davinci_param.
[01-14 14:23:27][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:27][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:27][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

get 0-0-0-0.000000-0-0-0
[01-14 14:23:27][pid:835][SYSINIT][ERROR]device not support RS485
[01-14 14:23:27][pid:835][HW_IF][ERROR]transfer_485_config_options error [options:57]
davinci receive cmd_query_davinci_param.
[01-14 14:23:27][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:27][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:27][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

IEfile uncompressed.
davinci receive cmd_query_davinci_param.
[01-14 14:23:28][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:28][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:28][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:29][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:29][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:29][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:30][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:30][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:30][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:31][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:31][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:31][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:32][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:32][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:32][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:init_dsp_lib() begin
<DSP> DBG:init_dsp_lib() end
[01-14 14:23:33][pid:835][DSP][ERROR][2]g_pdsp->audioTBShare.frameLen=80, g_pdsp->audioTBShare.totalFrame=128..
davinci receive cmd_query_davinci_param.
[01-14 14:23:33][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:33][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:33][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

mknod: /dev/snd/controlC0: File exists
mknod: /dev/snd/pcmC0D0c: File exists
mknod: /dev/snd/pcmC0D0p: File exists
[01-14 14:23:33][pid:835][HW_IF][ERROR]<read_fixed_noise_info_from_flash> (CFG_MAGIC != read.magicNumber(ffffffff)
davinci receive cmd_query_davinci_param.
[01-14 14:23:34][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:34][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:34][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:35][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:35][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:35][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:36][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:36][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:36][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:37][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:37][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:37][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

# davinci receive cmd_query_davinci_param.
[01-14 14:23:38][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:38][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:38][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:23:39][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:39][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:39][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:setup_dsp() begin
<DSP> DBG:init_cmem_module:cached_size=33030144(31M),noncached_size=6815744(6M)
init_cmem_module:CMEM_cmdline=insmod /dav/cmemk.ko phys_start=0xc6600000 phys_end=0xc8c00000 pools=1x33030144,1x6815744

davinci receive cmd_query_davinci_param.
[01-14 14:23:40][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:40][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:40][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

gdma Init Successful
b_fd=0,b_smd=1,b_scd=0
channel 1 is not 1 or 2<DSP> DBG:DSP start with Vout:Disabled,Audio:Disabled,VT:Disabled,MD:Enabled, vsync_guard:Enabled,vout_osd: Disabled, oversampling:Disabled, roi: Enabled, primacy: Disabled . hdr mode Disabled qr Disabled
<DSP> DBG:dsp_object.device_mode 0
<DSP> DBG:enc channel cnt 2, delay mode 0
Use CMEM buffer!
goto_idle done
pDspInitPara->VideoInitParam.capture_mode 125967385
find_video_mode sucusss!! mode 125967385 p_mode_table.vin_mode 30 vin_object.vin_fps 25.000000 vin w 1920 h 1080
set mode 30 type 21
vin_mode 2304*1296 vin_mode_temp 2304*1296 vin_mode_temp2 2304*1296#######pDspInitPara vout enable 0
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=0,maxRate(maxFps)=25.000000,fps=0x1
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=1.000000,clockStep=45000
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=0,fps=0x1,fpsFlg=0x1,frmPerSec=1,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=1,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=1,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=1,encode_type=1, (1920x1080), mirror type0, I inerval 50, bps 4014,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 1> in None MotionJPEG, skip!
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=2,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=2,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=2,encode_type=1, (352x288), mirror type0, I inerval 50, bps 501,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 2> in None MotionJPEG, skip!

overlay: start = 0x43c71000, total size = 0x100000 ( bytes)
b_rotate 0 overlay_level64 width 1920 height 1072
osd_width 1280 osd_scale_first 64 total 81920
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
init osd memory ok
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 1
chan 2, osd size 0 osd_size_changed 1
b_rotate 0 overlay_level16 width 1920 height 1072
osd_width 1280 osd_scale_first 16 total 20480
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=0,flgOsd=0x1, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=1,flgOsd=0x3, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
davinci receive cmd_query_davinci_param.
[01-14 14:23:41][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:41][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:41][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=2,flgOsd=0x7, bStart=1
init osd success
<VidThrd> DBG:setup_video_input begin
<VidThrd> ERR:Please load source driver!
<VidThrd> ERR:set video source failed!
<DSP> ERR:setup_dsp:setup_video_input
[01-14 14:23:41][pid:835][DSP][ERROR]DSP 初始化失败...
[01-14 14:23:41][pid:835][SYSINIT][ERROR]hwif_dsp_init error force sys reboot,ret=-12!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:23:42][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:23:42][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:23:42][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 1

U-Boot 1.3.4-84026 (Jul 16 2014 - 16:51:43)

ARM Clock: 480MHz
DDR Clock: 336MHz
Hit Ctrl+u to stop autoboot: 2Hit Ctrl+u to stop autoboot: 1Hit Ctrl+u to stop autoboot: 0
|RCV UDP pack timeout|
Unknown command:null
nand booting ...
load kernel...
load ramdisk...
init started: BusyBox v1.19.3 (2014-07-11 11:25:54 CST)
starting pid 375, tty '': '/etc/init.d/rcS'
Starting udev: [ OK ]
starting pid 606, tty '': '/sbin/iptables -A INPUT -p tcp --dport 23 -j DROP'
starting pid 607, tty '': '/sbin/iptables -A INPUT -p tcp --dport 22 -j DROP'
starting pid 608, tty '': '/sbin/iptables -A INPUT -p tcp --dport 21 -j DROP'
starting pid 609, tty '': '/sbin/inetd -f -e /etc/inetd.conf'
starting pid 610, tty '': '-/bin/sh'


BusyBox v1.19.3 (2014-07-11 11:25:54 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

UBI device number 1, total 192 LEBs (24772608 bytes, 23.6 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi1_0.
Check dir /dav ok! (0)
UBI device number 3, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi3_0.
Check dir /davinci ok! (0)
UBI device number 4, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi4_0.
Check dir /config ok! (0)
Hit Ctrl+c to stop and exec /home/initrun.sh to continue
route: ioctl 0x890c failed: No such process
/dav
map_size = 0x300000
nr_item = 3
addr_offset = 0x0 filename = orccode.bin
addr_offset = 0x200000 filename = orcme.bin
addr_offset = 0x2a0000 filename = default_binary.bin
mmap returns 0x402e6000
loading ./orccode.bin...addr = 0x402e6000, size = 0x19f02d
loading ./orcme.bin...addr = 0x404e6000, size = 0x36374
loading ./default_binary.bin...addr = 0x40586000, size = 0x40000
===============================
u_code version = 2013/10/24 3.0
===============================
ln: /dev/rtc: File exists
=====check_config start=====
===main db is ok===
start unix bus daemon
netprocess version: 1.0.13 [19:32:31-Jul 17 2014].
[01-14 14:24:08][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:24:08][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:24:08][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
[01-14 14:24:08][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
==================PPPoE is disable!!!
No need to recover kernel pri partition.
No need to recover ramdisk pri partition.
[01-14 14:24:09][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
[01-14 14:24:09][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:24:09][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:24:09][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
davinci receive cmd_query_davinci_param.
[01-14 14:24:10][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:10][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:10][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

========capture_mode_pal=17, capture_mode_ntsc=18===============.
powerLineFrequencyMode = 0
@@@motion PAL!!!!!!!!!!!!!!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:24:11][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:11][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:11][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get 0-0-0-0.000000-0-0-0
davinci receive cmd_query_davinci_param.
[01-14 14:24:12][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:12][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:12][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

[01-14 14:24:12][pid:835][SYSINIT][ERROR]device not support RS485
[01-14 14:24:12][pid:835][HW_IF][ERROR]transfer_485_config_options error [options:57]
davinci receive cmd_query_davinci_param.
[01-14 14:24:12][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:12][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:12][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

IEfile uncompressed.
davinci receive cmd_query_davinci_param.
[01-14 14:24:13][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:13][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:13][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:14][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:14][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:14][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:15][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:15][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:15][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:16][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:16][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:16][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:17][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:17][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:17][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:init_dsp_lib() begin
<DSP> DBG:init_dsp_lib() end
[01-14 14:24:18][pid:835][DSP][ERROR][2]g_pdsp->audioTBShare.frameLen=80, g_pdsp->audioTBShare.totalFrame=128..
mknod: /dev/snd/controlC0: File exists
mknod: /dev/snd/pcmC0D0c: File exists
mknod: /dev/snd/pcmC0D0p: File exists
[01-14 14:24:18][pid:835][HW_IF][ERROR]<read_fixed_noise_info_from_flash> (CFG_MAGIC != read.magicNumber(ffffffff)
davinci receive cmd_query_davinci_param.
[01-14 14:24:18][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:18][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:18][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:19][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:19][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:19][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:20][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:20][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:20][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:21][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:21][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:21][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:22][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:22][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:22][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

# davinci receive cmd_query_davinci_param.
[01-14 14:24:23][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:23][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:23][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:24][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:24][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:24][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:setup_dsp() begin
<DSP> DBG:init_cmem_module:cached_size=33030144(31M),noncached_size=6815744(6M)
init_cmem_module:CMEM_cmdline=insmod /dav/cmemk.ko phys_start=0xc6600000 phys_end=0xc8c00000 pools=1x33030144,1x6815744

davinci receive cmd_query_davinci_param.
[01-14 14:24:25][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:25][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:25][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

gdma Init Successful
b_fd=0,b_smd=1,b_scd=0
channel 1 is not 1 or 2<DSP> DBG:DSP start with Vout:Disabled,Audio:Disabled,VT:Disabled,MD:Enabled, vsync_guard:Enabled,vout_osd: Disabled, oversampling:Disabled, roi: Enabled, primacy: Disabled . hdr mode Disabled qr Disabled
<DSP> DBG:dsp_object.device_mode 0
<DSP> DBG:enc channel cnt 2, delay mode 0
Use CMEM buffer!
goto_idle done
pDspInitPara->VideoInitParam.capture_mode 125967385
find_video_mode sucusss!! mode 125967385 p_mode_table.vin_mode 30 vin_object.vin_fps 25.000000 vin w 1920 h 1080
set mode 30 type 21
vin_mode 2304*1296 vin_mode_temp 2304*1296 vin_mode_temp2 2304*1296#######pDspInitPara vout enable 0
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=0,maxRate(maxFps)=25.000000,fps=0x1
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=1.000000,clockStep=45000
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=0,fps=0x1,fpsFlg=0x1,frmPerSec=1,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=1,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=1,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=1,encode_type=1, (1920x1080), mirror type0, I inerval 50, bps 4014,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 1> in None MotionJPEG, skip!
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=2,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=2,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=2,encode_type=1, (352x288), mirror type0, I inerval 50, bps 501,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 2> in None MotionJPEG, skip!

overlay: start = 0x43ceb000, total size = 0x100000 ( bytes)
b_rotate 0 overlay_level64 width 1920 height 1072
osd_width 1280 osd_scale_first 64 total 81920
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
init osd memory ok
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 1
chan 2, osd size 0 osd_size_changed 1
b_rotate 0 overlay_level16 width 1920 height 1072
osd_width 1280 osd_scale_first 16 total 20480
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=0,flgOsd=0x1, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=1,flgOsd=0x3, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=2,flgOsd=0x7, bStart=1
init osd success
<VidThrd> DBG:setup_video_input begin
<VidThrd> ERR:Please load source driver!
<VidThrd> ERR:set video source failed!
<DSP> ERR:setup_dsp:setup_video_input
[01-14 14:24:26][pid:835][DSP][ERROR]DSP 初始化失败...
[01-14 14:24:26][pid:835][SYSINIT][ERROR]hwif_dsp_init error force sys reboot,ret=-12!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:24:26][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:26][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:26][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:27][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:27][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:27][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param



U-Boot 1.3.4-84026 (Jul 16 2014 - 16:51:43)

ARM Clock: 480MHz
DDR Clock: 336MHz
Hit Ctrl+u to stop autoboot: 2Hit Ctrl+u to stop autoboot: 1Hit Ctrl+u to stop autoboot: 0
|RCV UDP pack timeout|
Unknown command:null
nand booting ...
load kernel...
load ramdisk...
init started: BusyBox v1.19.3 (2014-07-11 11:25:54 CST)
starting pid 375, tty '': '/etc/init.d/rcS'
Starting udev: [ OK ]
starting pid 606, tty '': '/sbin/iptables -A INPUT -p tcp --dport 23 -j DROP'
starting pid 607, tty '': '/sbin/iptables -A INPUT -p tcp --dport 22 -j DROP'
starting pid 608, tty '': '/sbin/iptables -A INPUT -p tcp --dport 21 -j DROP'
starting pid 609, tty '': '/sbin/inetd -f -e /etc/inetd.conf'
starting pid 610, tty '': '-/bin/sh'


BusyBox v1.19.3 (2014-07-11 11:25:54 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

UBI device number 1, total 192 LEBs (24772608 bytes, 23.6 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi1_0.
Check dir /dav ok! (0)
UBI device number 3, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi3_0.
Check dir /davinci ok! (0)
UBI device number 4, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi4_0.
Check dir /config ok! (0)
Hit Ctrl+c to stop and exec /home/initrun.sh to continue
route: ioctl 0x890c failed: No such process
/dav
map_size = 0x300000
nr_item = 3
addr_offset = 0x0 filename = orccode.bin
addr_offset = 0x200000 filename = orcme.bin
addr_offset = 0x2a0000 filename = default_binary.bin
mmap returns 0x402ff000
loading ./orccode.bin...addr = 0x402ff000, size = 0x19f02d
loading ./orcme.bin...addr = 0x404ff000, size = 0x36374
loading ./default_binary.bin...addr = 0x4059f000, size = 0x40000
===============================
u_code version = 2013/10/24 3.0
===============================
ln: /dev/rtc: File exists
=====check_config start=====
===main db is ok===
start unix bus daemon
netprocess version: 1.0.13 [19:32:31-Jul 17 2014].
[01-14 14:24:53][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:24:53][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:24:53][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
[01-14 14:24:53][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
==================PPPoE is disable!!!
No need to recover kernel pri partition.
No need to recover ramdisk pri partition.
davinci receive cmd_query_davinci_param.
[01-14 14:24:54][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:54][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:54][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:55][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:55][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:55][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

========capture_mode_pal=17, capture_mode_ntsc=18===============.
powerLineFrequencyMode = 0
@@@motion PAL!!!!!!!!!!!!!!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:24:56][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:56][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:56][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get 0-0-0-0.000000-0-0-0
davinci receive cmd_query_davinci_param.
[01-14 14:24:57][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:57][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:57][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

[01-14 14:24:57][pid:835][SYSINIT][ERROR]device not support RS485
[01-14 14:24:57][pid:835][HW_IF][ERROR]transfer_485_config_options error [options:57]
davinci receive cmd_query_davinci_param.
[01-14 14:24:57][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:57][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:57][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

IEfile uncompressed.
davinci receive cmd_query_davinci_param.
[01-14 14:24:58][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:58][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:58][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:24:59][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:24:59][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:24:59][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:00][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:00][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:00][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:01][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:01][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:01][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:02][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:02][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:02][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:init_dsp_lib() begin
<DSP> DBG:init_dsp_lib() end
[01-14 14:25:03][pid:835][DSP][ERROR][2]g_pdsp->audioTBShare.frameLen=80, g_pdsp->audioTBShare.totalFrame=128..
mknod: /dev/snd/controlC0: File exists
mknod: /dev/snd/pcmC0D0c: File exists
mknod: /dev/snd/pcmC0D0p: File exists
[01-14 14:25:03][pid:835][HW_IF][ERROR]<read_fixed_noise_info_from_flash> (CFG_MAGIC != read.magicNumber(ffffffff)
davinci receive cmd_query_davinci_param.
[01-14 14:25:03][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:03][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:03][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:04][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:04][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:04][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:05][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:05][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:05][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:06][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:06][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:06][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:07][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:07][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:07][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

# davinci receive cmd_query_davinci_param.
[01-14 14:25:08][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:08][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:08][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:09][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:09][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:09][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:setup_dsp() begin
<DSP> DBG:init_cmem_module:cached_size=33030144(31M),noncached_size=6815744(6M)
init_cmem_module:CMEM_cmdline=insmod /dav/cmemk.ko phys_start=0xc6600000 phys_end=0xc8c00000 pools=1x33030144,1x6815744

davinci receive cmd_query_davinci_param.
[01-14 14:25:10][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:10][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:10][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

gdma Init Successful
b_fd=0,b_smd=1,b_scd=0
channel 1 is not 1 or 2<DSP> DBG:DSP start with Vout:Disabled,Audio:Disabled,VT:Disabled,MD:Enabled, vsync_guard:Enabled,vout_osd: Disabled, oversampling:Disabled, roi: Enabled, primacy: Disabled . hdr mode Disabled qr Disabled
<DSP> DBG:dsp_object.device_mode 0
<DSP> DBG:enc channel cnt 2, delay mode 0
Use CMEM buffer!
goto_idle done
pDspInitPara->VideoInitParam.capture_mode 125967385
find_video_mode sucusss!! mode 125967385 p_mode_table.vin_mode 30 vin_object.vin_fps 25.000000 vin w 1920 h 1080
set mode 30 type 21
vin_mode 2304*1296 vin_mode_temp 2304*1296 vin_mode_temp2 2304*1296#######pDspInitPara vout enable 0
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=0,maxRate(maxFps)=25.000000,fps=0x1
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=1.000000,clockStep=45000
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=0,fps=0x1,fpsFlg=0x1,frmPerSec=1,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=1,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=1,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=1,encode_type=1, (1920x1080), mirror type0, I inerval 50, bps 4014,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 1> in None MotionJPEG, skip!
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=2,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=2,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=2,encode_type=1, (352x288), mirror type0, I inerval 50, bps 501,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 2> in None MotionJPEG, skip!

overlay: start = 0x43a6b000, total size = 0x100000 ( bytes)
b_rotate 0 overlay_level64 width 1920 height 1072
osd_width 1280 osd_scale_first 64 total 81920
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
init osd memory ok
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 1
chan 2, osd size 0 osd_size_changed 1
b_rotate 0 overlay_level16 width 1920 height 1072
osd_width 1280 osd_scale_first 16 total 20480
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=0,flgOsd=0x1, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=1,flgOsd=0x3, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=2,flgOsd=0x7, bStart=1
init osd success
<VidThrd> DBG:setup_video_input begin
<VidThrd> ERR:Please load source driver!
<VidThrd> ERR:set video source failed!
<DSP> ERR:setup_dsp:setup_video_input
[01-14 14:25:11][pid:835][DSP][ERROR]DSP 初始化失败...
[01-14 14:25:11][pid:835][SYSINIT][ERROR]hwif_dsp_init error force sys reboot,ret=-12!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:25:11][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:11][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:11][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:12][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:12][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:12][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param



U-Boot 1.3.4-84026 (Jul 16 2014 - 16:51:43)

ARM Clock: 480MHz
DDR Clock: 336MHz
Hit Ctrl+u to stop autoboot: 2Hit Ctrl+u to stop autoboot: 1Hit Ctrl+u to stop autoboot: 0
|RCV UDP pack timeout|
Unknown command:null
nand booting ...
load kernel...
load ramdisk...
init started: BusyBox v1.19.3 (2014-07-11 11:25:54 CST)
starting pid 375, tty '': '/etc/init.d/rcS'
Starting udev: [ OK ]
starting pid 606, tty '': '/sbin/iptables -A INPUT -p tcp --dport 23 -j DROP'
starting pid 607, tty '': '/sbin/iptables -A INPUT -p tcp --dport 22 -j DROP'
starting pid 608, tty '': '/sbin/iptables -A INPUT -p tcp --dport 21 -j DROP'
starting pid 609, tty '': '/sbin/inetd -f -e /etc/inetd.conf'
starting pid 610, tty '': '-/bin/sh'


BusyBox v1.19.3 (2014-07-11 11:25:54 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

UBI device number 1, total 192 LEBs (24772608 bytes, 23.6 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi1_0.
Check dir /dav ok! (0)
UBI device number 3, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi3_0.
Check dir /davinci ok! (0)
UBI device number 4, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi4_0.
Check dir /config ok! (0)
Hit Ctrl+c to stop and exec /home/initrun.sh to continue
route: ioctl 0x890c failed: No such process
/dav
map_size = 0x300000
nr_item = 3
addr_offset = 0x0 filename = orccode.bin
addr_offset = 0x200000 filename = orcme.bin
addr_offset = 0x2a0000 filename = default_binary.bin
mmap returns 0x402e8000
loading ./orccode.bin...addr = 0x402e8000, size = 0x19f02d
loading ./orcme.bin...addr = 0x404e8000, size = 0x36374
loading ./default_binary.bin...addr = 0x40588000, size = 0x40000
===============================
u_code version = 2013/10/24 3.0
===============================
ln: /dev/rtc: File exists
=====check_config start=====
===main db is ok===
start unix bus daemon
netprocess version: 1.0.13 [19:32:31-Jul 17 2014].
[01-14 14:25:39][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:25:39][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:25:39][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
[01-14 14:25:39][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
==================PPPoE is disable!!!
No need to recover kernel pri partition.
No need to recover ramdisk pri partition.
davinci receive cmd_query_davinci_param.
[01-14 14:25:40][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:40][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:40][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

========capture_mode_pal=17, capture_mode_ntsc=18===============.
powerLineFrequencyMode = 0
davinci receive cmd_query_davinci_param.
[01-14 14:25:41][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:41][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:41][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

@@@motion PAL!!!!!!!!!!!!!!!!!
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
davinci receive cmd_query_davinci_param.
[01-14 14:25:42][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:42][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:42][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

get 0-0-0-0.000000-0-0-0
[01-14 14:25:43][pid:835][SYSINIT][ERROR]device not support RS485
[01-14 14:25:43][pid:835][HW_IF][ERROR]transfer_485_config_options error [options:57]
davinci receive cmd_query_davinci_param.
[01-14 14:25:43][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:43][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:43][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:42][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:42][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:42][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

IEfile uncompressed.
davinci receive cmd_query_davinci_param.
[01-14 14:25:43][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:43][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:43][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:44][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:44][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:44][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:45][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:45][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:45][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:46][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:46][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:46][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:47][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:47][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:47][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:init_dsp_lib() begin
<DSP> DBG:init_dsp_lib() end
[01-14 14:25:48][pid:835][DSP][ERROR][2]g_pdsp->audioTBShare.frameLen=80, g_pdsp->audioTBShare.totalFrame=128..
mknod: /dev/snd/controlC0: File exists
mknod: /dev/snd/pcmC0D0c: File exists
mknod: /dev/snd/pcmC0D0p: File exists
[01-14 14:25:48][pid:835][HW_IF][ERROR]<read_fixed_noise_info_from_flash> (CFG_MAGIC != read.magicNumber(ffffffff)
davinci receive cmd_query_davinci_param.
[01-14 14:25:49][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:49][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:49][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:50][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:50][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:50][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:51][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:51][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:51][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:52][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:52][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:52][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:53][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:53][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:53][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

# davinci receive cmd_query_davinci_param.
[01-14 14:25:54][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:54][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:54][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:setup_dsp() begin
<DSP> DBG:init_cmem_module:cached_size=33030144(31M),noncached_size=6815744(6M)
init_cmem_module:CMEM_cmdline=insmod /dav/cmemk.ko phys_start=0xc6600000 phys_end=0xc8c00000 pools=1x33030144,1x6815744

davinci receive cmd_query_davinci_param.
[01-14 14:25:55][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:55][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:55][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:56][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:56][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:56][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

gdma Init Successful
b_fd=0,b_smd=1,b_scd=0
channel 1 is not 1 or 2<DSP> DBG:DSP start with Vout:Disabled,Audio:Disabled,VT:Disabled,MD:Enabled, vsync_guard:Enabled,vout_osd: Disabled, oversampling:Disabled, roi: Enabled, primacy: Disabled . hdr mode Disabled qr Disabled
<DSP> DBG:dsp_object.device_mode 0
<DSP> DBG:enc channel cnt 2, delay mode 0
Use CMEM buffer!
goto_idle done
pDspInitPara->VideoInitParam.capture_mode 125967385
find_video_mode sucusss!! mode 125967385 p_mode_table.vin_mode 30 vin_object.vin_fps 25.000000 vin w 1920 h 1080
set mode 30 type 21
vin_mode 2304*1296 vin_mode_temp 2304*1296 vin_mode_temp2 2304*1296#######pDspInitPara vout enable 0
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=0,maxRate(maxFps)=25.000000,fps=0x1
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=1.000000,clockStep=45000
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=0,fps=0x1,fpsFlg=0x1,frmPerSec=1,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=1,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=1,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=1,encode_type=1, (1920x1080), mirror type0, I inerval 50, bps 4014,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 1> in None MotionJPEG, skip!
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=2,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=2,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=2,encode_type=1, (352x288), mirror type0, I inerval 50, bps 501,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 2> in None MotionJPEG, skip!

overlay: start = 0x43bbb000, total size = 0x100000 ( bytes)
b_rotate 0 overlay_level64 width 1920 height 1072
osd_width 1280 osd_scale_first 64 total 81920
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
init osd memory ok
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 1
chan 2, osd size 0 osd_size_changed 1
b_rotate 0 overlay_level16 width 1920 height 1072
osd_width 1280 osd_scale_first 16 total 20480
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=0,flgOsd=0x1, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=1,flgOsd=0x3, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=2,flgOsd=0x7, bStart=1
init osd success
<VidThrd> DBG:setup_video_input begin
<VidThrd> ERR:Please load source driver!
<VidThrd> ERR:set video source failed!
<DSP> ERR:setup_dsp:setup_video_input
[01-14 14:25:56][pid:835][DSP][ERROR]DSP 初始化失败...
[01-14 14:25:56][pid:835][SYSINIT][ERROR]hwif_dsp_init error force sys reboot,ret=-12!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:25:57][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:57][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:57][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:25:58][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:25:58][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:25:58][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param



U-Boot 1.3.4-84026 (Jul 16 2014 - 16:51:43)

ARM Clock: 480MHz
DDR Clock: 336MHz
Hit Ctrl+u to stop autoboot: 2Hit Ctrl+u to stop autoboot: 1Hit Ctrl+u to stop autoboot: 0
|RCV UDP pack timeout|
Unknown command:null
nand booting ...
load kernel...
load ramdisk...
init started: BusyBox v1.19.3 (2014-07-11 11:25:54 CST)
starting pid 375, tty '': '/etc/init.d/rcS'
Starting udev: [ OK ]
starting pid 606, tty '': '/sbin/iptables -A INPUT -p tcp --dport 23 -j DROP'
starting pid 607, tty '': '/sbin/iptables -A INPUT -p tcp --dport 22 -j DROP'
starting pid 608, tty '': '/sbin/iptables -A INPUT -p tcp --dport 21 -j DROP'
starting pid 609, tty '': '/sbin/inetd -f -e /etc/inetd.conf'
starting pid 610, tty '': '-/bin/sh'


BusyBox v1.19.3 (2014-07-11 11:25:54 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.

UBI device number 1, total 192 LEBs (24772608 bytes, 23.6 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi1_0.
Check dir /dav ok! (0)
UBI device number 3, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi3_0.
Check dir /davinci ok! (0)
UBI device number 4, total 32 LEBs (4128768 bytes, 3.9 MiB), available 0 LEBs (0 bytes), LEB size 129024 bytes (126.0 KiB)
waiting for /dev/ubi4_0.
Check dir /config ok! (0)
Hit Ctrl+c to stop and exec /home/initrun.sh to continue
route: ioctl 0x890c failed: No such process
/dav
map_size = 0x300000
nr_item = 3
addr_offset = 0x0 filename = orccode.bin
addr_offset = 0x200000 filename = orcme.bin
addr_offset = 0x2a0000 filename = default_binary.bin
mmap returns 0x40314000
loading ./orccode.bin...addr = 0x40314000, size = 0x19f02d
loading ./orcme.bin...addr = 0x40514000, size = 0x36374
loading ./default_binary.bin...addr = 0x405b4000, size = 0x40000
===============================
u_code version = 2013/10/24 3.0
===============================
ln: /dev/rtc: File exists
=====check_config start=====
===main db is ok===
start unix bus daemon
netprocess version: 1.0.13 [19:32:31-Jul 17 2014].
[01-14 14:26:23][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:26:23][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:26:23][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
[01-14 14:26:23][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
==================PPPoE is disable!!!
No need to recover kernel pri partition.
No need to recover ramdisk pri partition.
[01-14 14:26:24][pid:821][IPC_UNIX][ERROR]daemon can not find Dst process.load_type 0x10012 is_need_ack 1
[01-14 14:26:24][pid:826][IPC_UNIX][ERROR] from daemon ack, dst not work len 0 , load_type is [10012]
[01-14 14:26:24][pid:826][UNI_IF][ERROR]65554:ipc_unix_call_service failed, ret = -3.
[01-14 14:26:24][pid:826][UNI_IF][ERROR]communicaite_to_davinci failed!!!
davinci receive cmd_query_davinci_param.
[01-14 14:26:25][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:25][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:25][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

========capture_mode_pal=17, capture_mode_ntsc=18===============.
powerLineFrequencyMode = 0
@@@motion PAL!!!!!!!!!!!!!!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:26:26][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:26][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:26][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get samplerate [2]
get 0-0-0-0.000000-0-0-0
davinci receive cmd_query_davinci_param.
[01-14 14:26:27][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:27][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:27][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

[01-14 14:26:27][pid:835][SYSINIT][ERROR]device not support RS485
[01-14 14:26:27][pid:835][HW_IF][ERROR]transfer_485_config_options error [options:57]
davinci receive cmd_query_davinci_param.
[01-14 14:26:27][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:27][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:27][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

IEfile uncompressed.
davinci receive cmd_query_davinci_param.
[01-14 14:26:28][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:28][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:28][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:29][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:29][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:29][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:30][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:30][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:30][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:31][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:31][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:31][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:32][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:32][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:32][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:init_dsp_lib() begin
<DSP> DBG:init_dsp_lib() end
[01-14 14:26:33][pid:835][DSP][ERROR][2]g_pdsp->audioTBShare.frameLen=80, g_pdsp->audioTBShare.totalFrame=128..
mknod: /dev/snd/controlC0: File exists
mknod: /dev/snd/pcmC0D0c: File exists
mknod: /dev/snd/pcmC0D0p: File exists
[01-14 14:26:33][pid:835][HW_IF][ERROR]<read_fixed_noise_info_from_flash> (CFG_MAGIC != read.magicNumber(ffffffff)
davinci receive cmd_query_davinci_param.
[01-14 14:26:33][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:33][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:33][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:34][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:34][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:34][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:35][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:35][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:35][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:36][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:36][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:36][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:37][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:37][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:37][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

# davinci receive cmd_query_davinci_param.
[01-14 14:26:38][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:38][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:38][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:39][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:39][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:39][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

<DSP> DBG:setup_dsp() begin
<DSP> DBG:init_cmem_module:cached_size=33030144(31M),noncached_size=6815744(6M)
init_cmem_module:CMEM_cmdline=insmod /dav/cmemk.ko phys_start=0xc6600000 phys_end=0xc8c00000 pools=1x33030144,1x6815744

davinci receive cmd_query_davinci_param.
[01-14 14:26:40][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:40][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:40][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

gdma Init Successful
b_fd=0,b_smd=1,b_scd=0
channel 1 is not 1 or 2<DSP> DBG:DSP start with Vout:Disabled,Audio:Disabled,VT:Disabled,MD:Enabled, vsync_guard:Enabled,vout_osd: Disabled, oversampling:Disabled, roi: Enabled, primacy: Disabled . hdr mode Disabled qr Disabled
<DSP> DBG:dsp_object.device_mode 0
<DSP> DBG:enc channel cnt 2, delay mode 0
Use CMEM buffer!
goto_idle done
pDspInitPara->VideoInitParam.capture_mode 125967385
find_video_mode sucusss!! mode 125967385 p_mode_table.vin_mode 30 vin_object.vin_fps 25.000000 vin w 1920 h 1080
set mode 30 type 21
vin_mode 2304*1296 vin_mode_temp 2304*1296 vin_mode_temp2 2304*1296#######pDspInitPara vout enable 0
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=0,maxRate(maxFps)=25.000000,fps=0x1
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=1.000000,clockStep=45000
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=0,fps=0x1,fpsFlg=0x1,frmPerSec=1,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=1,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=1,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=1,encode_type=1, (1920x1080), mirror type0, I inerval 50, bps 4014,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 1> in None MotionJPEG, skip!
<VidThrd> DBG:update_encode_fps_ctrl: Begin chan=2,maxRate(maxFps)=25.000000,fps=0x19
<VidThrd> DBG:update_encode_fps_ctrl: f_frame_rate=25.000000,clockStep=1800
<VidThrd> DBG:update_encode_fps_ctrl:f_frame_rate=25.000000,[25].clockStep=1800,[25]
<VidThrd> DBG:update_encode_fps_ctrl:Finally chan=2,fps=0x19,fpsFlg=0x1ffffff,frmPerSec=25,fpsCounter=0,fpsCycle=25,g_md_interval 5 ms
<VidThrd> DBG:update_video_config_param: chan=2,encode_type=1, (352x288), mirror type0, I inerval 50, bps 501,quality 60 i_quant 29, complexity 1 rate_type 0,p_encode_param->f_frame_rate 25.000000,svc mode 0 qp 6
<chan 2> in None MotionJPEG, skip!

overlay: start = 0x43bd8000, total size = 0x100000 ( bytes)
b_rotate 0 overlay_level64 width 1920 height 1072
osd_width 1280 osd_scale_first 64 total 81920
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
init osd memory ok
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 1
chan 2, osd size 0 osd_size_changed 1
b_rotate 0 overlay_level16 width 1920 height 1072
osd_width 1280 osd_scale_first 16 total 20480
b_rotate 0 overlay_level16 width 352 height 288
osd_width 256 osd_scale_first 16 sub total 4096
init osd area success
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=0,flgOsd=0x1, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=1,flgOsd=0x3, bStart=1
<OSD> DBG:Left=0 pChar->pos=4000000
<SetOsd()> line=0 y=64 line_char_count=16, valid char count 24,osd_lines 0
<SetOsd()> line=1 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=2 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=3 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=4 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=5 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=6 y=0 line_char_count=0, valid char count 0,osd_lines 0
<SetOsd()> line=7 y=0 line_char_count=0, valid char count 0,osd_lines 0
chan 1, osd size 0 osd_size_changed 0
chan 2, osd size 0 osd_size_changed 0
<OSD> DBG:setosd ok
<OSD> DBG:setosd:END. chan=2,flgOsd=0x7, bStart=1
init osd success
<VidThrd> DBG:setup_video_input begin
<VidThrd> ERR:Please load source driver!
<VidThrd> ERR:set video source failed!
<DSP> ERR:setup_dsp:setup_video_input
[01-14 14:26:41][pid:835][DSP][ERROR]DSP 初始化失败...
[01-14 14:26:41][pid:835][SYSINIT][ERROR]hwif_dsp_init error force sys reboot,ret=-12!!!!
davinci receive cmd_query_davinci_param.
[01-14 14:26:41][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:41][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:41][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

davinci receive cmd_query_davinci_param.
[01-14 14:26:42][pid:835][OTHER][ERROR]get_ipaddr ioctl error and errno=99
[01-14 14:26:42][pid:835][OTHER][ERROR]get_ipaddr failed.
[01-14 14:26:42][pid:835][OTHER][ERROR]inet_aton failed ,errno = 99, ip =
S: cmd_query_davinci_param

 
Hello all hik spec`s,

I purchased one DS-2CD2332-I camera from outlet, but it`s not working.
Started to search for some solutions and tried TFTP with each firmware staring from 5.2.0 - 5.4.5.
Update is successful, but after power cycle the camera goes in reboot loop, bellow terminal log with 5.2.0

Any ideas/suggestion`s?

Ctrl+u not stoping boot loader, also entered key`s are shown on screen like more than one symbol.

found a solution based on error "hwif_dsp_init error force sys reboot,ret=-12 ", thr suggestion was to disconnect and reconnect cameras flat cable.
My camera is working now :)
 
Ctrl+u not stoping boot loader, also entered key`s are shown on screen like more than one symbol.
I know you've fixed the problem by re-seating the ribbon cable to the sensor module - but maybe worth commenting for future use :

If you can't stop the bootloader, and what you type does not show correctly, it suggests the serial TTL connection to the camera is not wired correctly.
Is it wired like this example (camera connector is the same as the NVR)?
 
I know you've fixed the problem by re-seating the ribbon cable to the sensor module - but maybe worth commenting for future use :

If you can't stop the bootloader, and what you type does not show correctly, it suggests the serial TTL connection to the camera is not wired correctly.
Is it wired like this example (camera connector is the same as the NVR)?

According to you pinout example an all others I found, I could not get any response in putty.

But only with this I can get cameras activity on putty
TTL RX - PIN3 Camera
TX - PIN 1
GND - PIN 2

For example when I press key A in putty I receive back A&
 
What happens when you swap the connections to 1 and 2 around?

Nothing in putty, complete silence - tried camera power cycle, restart putty session, PC with WIN 11 also XP
I have 3 USB TTL converts and wit all of them I get such behavior.
I also tried with other camera and got the same behavior.

The only thing which is not double checked is cable between TTL and camera, I assembled the ZH-4 connecter with the contact`s on wires by myself - it was purchased as separated components available local shop.
Checked it with multimeter, no shortcut between pin wires... .
Will order some "ready" pack from amazon.

BUT the overall main goal was reached why I purchased this camera - I bought couple NVR`s DS-7716NI-I4/16P(B) from auction and of course password was not known :D
Password extraction via PoE works like a charm.
NVR`s booloaders are on last fw where HKVS $ does not react on any command - this has direct RS232 connection with null modem cable.
 
  • Like
Reactions: alastairstevenson
Hello gents


Looking for some advise. Got some Chinese second hand bi-spectral cameras (DS-2TD1228T-2/QA) from local market place without knowing about whole firmware ordeal. Not a big deal as I just use translator to set it up and record both streams on my reolink RLN 36, but is it possible to convert it to English firmware?? English firmware is more recent too comparted to Chinese. Thanks in advance


1720422807262.png
1720422831627.png
 
Hi - hoping someone can help me. I have about 60x of the DS-2CD2332-1 and I cannot get them to upgrade through the web interface. They were originally on V5.1.2 140116 and I was able to get my test unit to upgrade to V5.2.0 140721 through the web interface, but no further. I'd like to enable the ONVIF functions but I don't believe they exist on this old firmware. They are in english and I believe they always have been.

When I try to upgrade to various 5.3 versions of the software, it immediately tells me that the firmware upgrade failed throug the web interface (using IE and placing the firmware file in the root of C:).

I'm trying the TFTP software to upgrade to one of the newer 5.3 firmwares, but the TFTP software never sees the camera. I can see the camera from the same computer with the SADP software and even tried to set the camera IP to 192.0.0.68 using that tool, but TFTP just reports "initialized" with IP of 192.0.0.128. I've tried two windows computers (same result) and using a POE injector instead of a POE switch (as suggested previously) and turned off windows firewall entirely. Used windows 10 and 11, same results.

Can anyone help me? I've already spent two days on this. Thanks
 
These may be Chinese cameras, in which case they will reject EN/ML firmware.
This can probably be confirmed by checking the letters in the serial number - can you supply a sample?
If so, the brickfix method could be used to change the camera region / language.
The language can also be confirmed by inspection of the contents of mtd6 as per the method of this thread.
 
Hi - hoping someone can help me. I have about 60x of the DS-2CD2332-1 and I cannot get them to upgrade through the web interface. They were originally on V5.1.2 140116 and I was able to get my test unit to upgrade to V5.2.0 140721 through the web interface, but no further. I'd like to enable the ONVIF functions but I don't believe they exist on this old firmware. They are in english and I believe they always have been.

When I try to upgrade to various 5.3 versions of the software, it immediately tells me that the firmware upgrade failed throug the web interface (using IE and placing the firmware file in the root of C:).

I'm trying the TFTP software to upgrade to one of the newer 5.3 firmwares, but the TFTP software never sees the camera. I can see the camera from the same computer with the SADP software and even tried to set the camera IP to 192.0.0.68 using that tool, but TFTP just reports "initialized" with IP of 192.0.0.128. I've tried two windows computers (same result) and using a POE injector instead of a POE switch (as suggested previously) and turned off windows firewall entirely. Used windows 10 and 11, same results.

Can anyone help me? I've already spent two days on this. Thanks

When you try the tftp method, how are the computer and camera connected to each other? Direct ethernet with a cross over cable? Network switch? I have experienced problems with the tftp server not finding the camera with certain netgear switches even though the computer could see it in SADP.
 
I figured it out actually - I factory reset the camera via the web GUI (which I had not previously done) and when it came back up, the TFTP program finally found it and installed version 5.3.
After a few reboots I could see the camera accepted 5.3 via the SADP program and was able to access the web GUI again.
I could then upgrade the camera via the firmware files provided in the start of this thread all the way to 5.4.800 with just the webGUI.
Unfortunately to add ONVIF functionality I think I needed at least v5.5 on the camera, but it doesn't appear they made that upgrade for my camera.

Thanks for the response!
 
Well done for sorting that out.

I have a vague recollection that on that firmware ONVIF is a standard feature that does not need to be explicitly enabled.
How are you testing for ONVIF capability?
If you haven't already tried it, ONVIF Device Manager (sourceforge) works well to find ONVIF devices.
 
Hi All

I have the following cameras and I'm trying to use the brick fix V2 to upgrade without any success.

I used Windows XP, Windows 7, and now Linux with Scott py script

It is a Chinese version converted to English by the sound of it

Can anyone provide some guidance on the next step ?


ModelDS-2CD3132F-IWS
Serial No.DS-2CD3132F-IWS20150828CCCHxxxx
Firmware VersionV5.2.5 build 141201
Encoding VersionV5.0 build 140714

FYI the cameras are working fine, I just don't like the firmware version.

Thanks
 
What step have you tried so far?
I use the brick V2 firmware , try both the english and Chinese version

I have connected my laptop to a stand-alone POE switch with PC on 192.0.0.128 and cam on 192.0.0.64 with HIk TFTP , no success

tried on 192.168.1.128 also no success

tried on WinXP, on windows 7 and finally on Ubuntu with Scott python script

SAPD can see the cam and I can also ping it but the TFTP refuse to work :mad:
 
I use the brick V2 firmware , try both the english and Chinese version

I have connected my laptop to a stand-alone POE switch with PC on 192.0.0.128 and cam on 192.0.0.64 with HIk TFTP , no success

tried on 192.168.1.128 also no success

tried on WinXP, on windows 7 and finally on Ubuntu with Scott python script

SAPD can see the cam and I can also ping it but the TFTP refuse to work :mad:
If your camera is still working, you just need to flash it with the suggested firmware from this article
after that, your camera will become European forever.
 
  • Like
Reactions: Fred73