Thanks, just upgraded and it looks good. I just can't find the access card reader module setup anywhere. Any hints where I can find it?
VTO2000A new V4 firmware
- Thread starter riogrande75
- Start date
hello,
Just to confirm does SIP version of VTO and SIP version of VTH connect and work with each other?
I have upgraded to latest versions but struggling getting VTO to ring the VTH. VTH can see it but it is not fully connected.
VTO is on:
General_VTOXXX_Eng_P_16M_SIP_V4.300.0000000.2.R.20200313
VTH is on:
General_VTH151X_Eng_SIP_V4.300.0000000.8.R.20190316
Any ideas?
Just to confirm does SIP version of VTO and SIP version of VTH connect and work with each other?
I have upgraded to latest versions but struggling getting VTO to ring the VTH. VTH can see it but it is not fully connected.
VTO is on:
General_VTOXXX_Eng_P_16M_SIP_V4.300.0000000.2.R.20200313
VTH is on:
General_VTH151X_Eng_SIP_V4.300.0000000.8.R.20190316
Any ideas?
Last edited:
I managed to get it working with non sip version but its on version 3. I am hoping to use the features on V4 regards to disabling voice commands.
Is it possible i need to update MCU or something to get the sip versions working?
Is it possible i need to update MCU or something to get the sip versions working?
Guys can anyone help on getting the latest sip version working between VTO and VTH please.
So let me explain my setup, i have a VTO2000a and VTH1660, i upgraded both of them to the latest SIP versions.
I did a factory default on both, setup new password on VTO and all good.
On the VTH under search i can see the VTO, i click on add, change password to correct one and can confirm VTH changes symbol next to IP that it can now see it.
Issue is on the top right on the VTH i can still see an X on VTO indicating it is not connected.
Is there some setting i am missing? How do i get the VTO calling VTH on sip version of the firmware.
Update:
Got it working, did not realise on sip firmware i had to configure SIP side of things.
dahuawiki.com
So let me explain my setup, i have a VTO2000a and VTH1660, i upgraded both of them to the latest SIP versions.
I did a factory default on both, setup new password on VTO and all good.
On the VTH under search i can see the VTO, i click on add, change password to correct one and can confirm VTH changes symbol next to IP that it can now see it.
Issue is on the top right on the VTH i can still see an X on VTO indicating it is not connected.
Is there some setting i am missing? How do i get the VTO calling VTH on sip version of the firmware.
Update:
Got it working, did not realise on sip firmware i had to configure SIP side of things.
DahuaWiki
dahuawiki.com
Last edited:
In the network configuration window, server sip of the vto you have to disable the sip and modify the values: in ip you have to go the same as in the vto, domain VDP, in the first password goes the one of the VTH, in username and password the same as the VTO, then re-enable and save the data.
In the VTH configure in the sip serer option the same IP data of the VTO, VDP domain, the password of the VTH and user and password of the VTO, sorry my English
Yes ,need to change the name on the vth 9100#0 and to the vto makenthensame change ,have the same problem and after make the changes y working fine
fabiangualdesi
n3wb
Hello Erik!
Im having the same problem. Can you help me with that mcu File cause I couldn find it. Thank you very much!!!
Hello,
After updating the firmware of my VTO2000a with "General_VTOXXX_Eng_P_16M_SIP_V4.300.0000000.1.R.20190305.bin" and the MCU with the firmware "General_VTO2000A-MCU_APP_V3.000.0000000.0.R.20181123.bin",
Then after updating the firmware of my VTH1510CH with "General_VTH151X_Eng_SIP_V4.300.0000000.8.R.20190316.bin" and the MCU with the firmware "General_VTH15X0CH-6_ENG_MCU_STM8S003K3_V8.000.0000.0.R.170825.bin".
Sources: Dahua VTO/VTH Firmware Link
I have configured my intercom by following this procedure: How to configure 1 VTO+1 VTH（SIP 4.3 Baseline)
During the 1st tests, the system works very well:
VTO to VTH call transmission: OK,
audio: OK,
video: OK.
After I finished my setup, I shut down all my system. When I started it, I had some problems:
VTO to VTH call transmission: OK,
audio: OK,
video: KO.
I have restarted the system several times without success.
I have reset the VTO and VHT to factory configuration. I reconfigured the VTO and the VTH:
VTO to VTH call transmission: OK,
audio: OK,
video: OK.
I restart the VTO:
VTO to VTH call transmission: OK,
audio: OK,
video: OK.
I restart the VTH:
VTO to VTH call transmission: OK,
audio: OK,
video: KO.
Have you ever had this problem ?
Thank you for your feedback.
Nono
After updating the firmware of my VTO2000a with "General_VTOXXX_Eng_P_16M_SIP_V4.300.0000000.1.R.20190305.bin" and the MCU with the firmware "General_VTO2000A-MCU_APP_V3.000.0000000.0.R.20181123.bin",
Then after updating the firmware of my VTH1510CH with "General_VTH151X_Eng_SIP_V4.300.0000000.8.R.20190316.bin" and the MCU with the firmware "General_VTH15X0CH-6_ENG_MCU_STM8S003K3_V8.000.0000.0.R.170825.bin".
Sources: Dahua VTO/VTH Firmware Link
I have configured my intercom by following this procedure: How to configure 1 VTO+1 VTH（SIP 4.3 Baseline)
During the 1st tests, the system works very well:
VTO to VTH call transmission: OK,
audio: OK,
video: OK.
After I finished my setup, I shut down all my system. When I started it, I had some problems:
VTO to VTH call transmission: OK,
audio: OK,
video: KO.
I have restarted the system several times without success.
I have reset the VTO and VHT to factory configuration. I reconfigured the VTO and the VTH:
VTO to VTH call transmission: OK,
audio: OK,
video: OK.
I restart the VTO:
VTO to VTH call transmission: OK,
audio: OK,
video: OK.
I restart the VTH:
VTO to VTH call transmission: OK,
audio: OK,
video: KO.
Have you ever had this problem ?
Thank you for your feedback.
Nono
Last edited:
Hy there Guys.
I have the following issue.
I have a VTO2000A-C-2 vith a VTO2000A-K, and it's Hooked to a VTH1510CH.
I can upgrade the VTH's firmware to 4.3 but the VTO's firmware wont go above 4.0. I tried everything.
The main issue is, that the keypad wont work.
I added it in the admin site to the facade layout, set a uniform password in the A&C settings, but it wont work.
Should the keypad light up after the VTO starts? And i should hear the "button sounds" to, when I type in the code.
Did anyone have such an issue?
I have the following issue.
I have a VTO2000A-C-2 vith a VTO2000A-K, and it's Hooked to a VTH1510CH.
I can upgrade the VTH's firmware to 4.3 but the VTO's firmware wont go above 4.0. I tried everything.
The main issue is, that the keypad wont work.
I added it in the admin site to the facade layout, set a uniform password in the A&C settings, but it wont work.
Should the keypad light up after the VTO starts? And i should hear the "button sounds" to, when I type in the code.
Did anyone have such an issue?
Attachments
If you run a very old firmware on your VTO2000A-2, you should try to use an older VDPconfig tool to upgrade to V4.3.
I guys!
I have a VTO2000A and a VTH1550CH.
I've upgraded both with last versions of firmware and MCU and I was able to configure everything fine (after some working hours).
Files I uploaded on VDPConfig:
First: General_VTH151X_Eng_SIP_V4.300.0000000.8.R.20190316.bin (11 698 Kb)
then: General_VTH151X_Eng_SIP_V4.300.0000000.8.R.20190316.language.bin (1 087 Kb)
There is a Upall_VTH151X.20190316.bin (16 384 Kb), but I don't know what it is for so I ignored it.
My problem is on my VTH that don't have the menu to change the language. It's in english but I need portuguese (because of others home users).
I updated to a multilanguage version, and I upload either .bin language file (before the upgrade of firmware) but nothing changes on screen.
What am I doing wrong?
I have a VTO2000A and a VTH1550CH.
I've upgraded both with last versions of firmware and MCU and I was able to configure everything fine (after some working hours).
Files I uploaded on VDPConfig:
First: General_VTH151X_Eng_SIP_V4.300.0000000.8.R.20190316.bin (11 698 Kb)
then: General_VTH151X_Eng_SIP_V4.300.0000000.8.R.20190316.language.bin (1 087 Kb)
There is a Upall_VTH151X.20190316.bin (16 384 Kb), but I don't know what it is for so I ignored it.
My problem is on my VTH that don't have the menu to change the language. It's in english but I need portuguese (because of others home users).
I updated to a multilanguage version, and I upload either .bin language file (before the upgrade of firmware) but nothing changes on screen.
What am I doing wrong?
Merry XMAS!
I have a problem with VTO2000A. When upgrade to version 4.3, when access to web manager, admin and password = admin in black list.
Pressing 5 times to do a reset doesn't work. With the riogrande75 manual restore the MCU,
I was still in pjotr_weliki manual to be able to connect by tftp.
SIP 2.0:
General.VTOXXX-Eng-P-16M-SIP-V3.300000.1.R.20190305
http://www.mediafire.com/file/xyg2m...Eng-P-16M-SIP-V4.300.0000000.1.R.20190305.zip
By tftp I have installed the firmware that riogrande75 has shared, and although when the process finishes it tells me that everything is OK. It doesn't get off the blacklist. I also don't understand how to install, for example, firmware 3.2 to leave the device of origin, there is only the "bin" file.
Any ideas?
Thank you.
I have a problem with VTO2000A. When upgrade to version 4.3, when access to web manager, admin and password = admin in black list.
Pressing 5 times to do a reset doesn't work. With the riogrande75 manual restore the MCU,
I was still in pjotr_weliki manual to be able to connect by tftp.
SIP 2.0:
General.VTOXXX-Eng-P-16M-SIP-V3.300000.1.R.20190305
http://www.mediafire.com/file/xyg2m...Eng-P-16M-SIP-V4.300.0000000.1.R.20190305.zip
By tftp I have installed the firmware that riogrande75 has shared, and although when the process finishes it tells me that everything is OK. It doesn't get off the blacklist. I also don't understand how to install, for example, firmware 3.2 to leave the device of origin, there is only the "bin" file.
Any ideas?
Thank you.
Did you try to use another browser?
As I see you are quite experienced with IT stuff, you might try Dahua Console to list complete config (use command "config all") and see admin password.
Don't know if you can reset the blacklisting, as I've never experienced that.
As I see you are quite experienced with IT stuff, you might try Dahua Console to list complete config (use command "config all") and see admin password.
Don't know if you can reset the blacklisting, as I've never experienced that.
I've never worked with python. But I'm going to give it a try. I test with all browers and the result is admin is in the blacklist.
Is possible flash this file by tftp??
SIP 2.0:
General.VTOXXX-Eng-P-16M-SIP-V3.300000.1.R.20190305
http://www.mediafire.com/file/xyg2m...Eng-P-16M-SIP-V4.300.0000000.1.R.20190305.zip
thanks
Is possible flash this file by tftp??
SIP 2.0:
General.VTOXXX-Eng-P-16M-SIP-V3.300000.1.R.20190305
http://www.mediafire.com/file/xyg2m...Eng-P-16M-SIP-V4.300.0000000.1.R.20190305.zip
thanks
Off course you could flash the firmware once again. The risk in destroying it completely is quite high.
What firmware version is on the device right now? Check it out with dahua toolbox.
Anyhow I don't see a sense in flashing a new fw. It won't change the configuration, so your admin remains blocked.
I'd rather try dahua console (you don't need to have any python knowledge) or do a factory reset.
What firmware version is on the device right now? Check it out with dahua toolbox.
Anyhow I don't see a sense in flashing a new fw. It won't change the configuration, so your admin remains blocked.
I'd rather try dahua console (you don't need to have any python knowledge) or do a factory reset.
No, I've never heard of a language pack for a VTO2000A containing greek. But if you find it, pls. let me know.