I did not check again once I got the camera up but I will this evening.
Review-Dahua IPC-HDBW4231F-E2-M Dual Starlight Cam
- Thread starter looney2ns
- Start date
Is anyone having issues viewing both live views in GDMSS? I can see the image from the second channel, but not the first... It simply never loads while all my other cameras and channel 2 load just fine.
Thoughts?
Also having issues with the settings. I can set everything via the NVR, however the image preview isn't present. I can also set the IVS rules, with a proper image preview, however the rules do not appear on any of the live views as they do on all my other cams.
Thoughts?
Also having issues with the settings. I can set everything via the NVR, however the image preview isn't present. I can also set the IVS rules, with a proper image preview, however the rules do not appear on any of the live views as they do on all my other cams.
giomania
IPCT Contributor
- Joined
- Jun 1, 2017
- Messages
- 780
- Reaction score
- 538
I installed mine tonight. After mounting on the ceiling, direct to drywall, the temperature with the cover off was 105.5 degrees, and 98.7 degrees with it on.
The only oddity I noted was that both channels were stuck in Black & White, despite the fact there was sufficient light to switch to color. My other Annke 161DR (HikVision Cube Cam clone) was in color in the same room.
I had the default settings under profile It was staying in black and white mode with default settings of Mode: Auto, Sensitivity: Middle, and Delay: 6S. I played around, and changing the sensitivity to High, and then changing mode to color, then switching mode back to Auto and saving made it "stick" in color mode.
Next I tested the switching back and forth. When I turn off lights, it switches to Black & White mode, but when I turn lights back on, it does not switch to color. None of my other Dahuas have exhibited this behavior, but this is the first one indoors, except for the garage, and it is also my first dome camera. I am done testing for now, and we will see how it goes from here on the switching tomorrow. I am not hopeful that some miraculous change will occur, so if anyone has any guidance on settings, "I'm Listening".
Mark
The only oddity I noted was that both channels were stuck in Black & White, despite the fact there was sufficient light to switch to color. My other Annke 161DR (HikVision Cube Cam clone) was in color in the same room.
I had the default settings under profile It was staying in black and white mode with default settings of Mode: Auto, Sensitivity: Middle, and Delay: 6S. I played around, and changing the sensitivity to High, and then changing mode to color, then switching mode back to Auto and saving made it "stick" in color mode.
Next I tested the switching back and forth. When I turn off lights, it switches to Black & White mode, but when I turn lights back on, it does not switch to color. None of my other Dahuas have exhibited this behavior, but this is the first one indoors, except for the garage, and it is also my first dome camera. I am done testing for now, and we will see how it goes from here on the switching tomorrow. I am not hopeful that some miraculous change will occur, so if anyone has any guidance on settings, "I'm Listening".
Mark
Mr_D
Getting comfortable
Interesting. On mine, one channel really likes to stay in color mode long past the point where all of the other starlights, including this camera's other channel, have switched to black and white. If I manually switch the B&W, then back to auto, it'll stay B&W for the night, then the issue repeats the following night.
beepsilver
Getting comfortable
I use bp2008's sunrise sunset utility to designate color for day and B&W for night to get around this. Can also set different zoom and focus for night and day which is very useful...
giomania
IPCT Contributor
- Joined
- Jun 1, 2017
- Messages
- 780
- Reaction score
- 538
Thank you for the info; that was my fallback plan.
Sent from my iPhone using Tapatalk Pro
looney2ns
IPCT Contributor
This is possibly a firmware issue. Out of all the cams I have reviewed and the ones I own, I've not ran into this issue.
also make certain the photo sensor is not misaligned and has a good view of ambient light.
Update on my issues -
A simple camera reset seems to have solved all the viewing issues, however it's not allowing me to set IVS rules. Smart PSS will not grant me access to set the rules and setting them via the NVR doesn't seem to work either. I can set the rule but it never appears on the live feed or seems to trigger.
Odd camera overall - some settings stick and others don't. I'm experiencing the same with the daylight/night issue above too.
A simple camera reset seems to have solved all the viewing issues, however it's not allowing me to set IVS rules. Smart PSS will not grant me access to set the rules and setting them via the NVR doesn't seem to work either. I can set the rule but it never appears on the live feed or seems to trigger.
Odd camera overall - some settings stick and others don't. I'm experiencing the same with the daylight/night issue above too.
looney2ns
IPCT Contributor
SmartPSS can be flaky, best to use either IE (not edge), Chrome with IE Tab extension installed, or Pale Moon 32bit browser.
You have do most IVS settings in the Cam's web Gui directly, then set them up in the NVR.
From a computer, You can also log into the NVR's web page, and get more setup options and the ability to connect directly to the cams.
You have do most IVS settings in the Cam's web Gui directly, then set them up in the NVR.
From a computer, You can also log into the NVR's web page, and get more setup options and the ability to connect directly to the cams.
usaf_pride
Pulling my weight
- Joined
- Mar 10, 2017
- Messages
- 284
- Reaction score
- 170
@looney2ns, curious how you are using SmartPSS. I have a NVR5216 that I set the default group to the NVR IP and then all cameras will display on the 2x2 correctly, but on the 3x3, this camera won't show. I'm wondering if I should drop the NVR from default group and add each camera individually to PSS. (I'm running a POE switch).
Hello @looney2ns Question for you: Did you place the camera at the maximum tilt on your pictures on the opening post? 65 degree angle?
looney2ns
IPCT Contributor
No I did not.Hello @looney2ns Question for you: Did you place the camera at the maximum tilt on your pictures on the opening post? 65 degree angle?
Mr_D
Getting comfortable
In the camera's web UI under the Settings tab, Conditions, Picture, there's a radio button to mirror the output right above the flip dropdown.
I just checked Empire Tech Aliexpress store and I don't see it for sale? Where do I buy one and what's the price?
Also, how does the quality compare to the HDW5231R-ZE? I want to buy one of those too but I didn't see any comparison talk. I'm doing a new three cam setup, two in front and one in back of house.
Also, how does the quality compare to the HDW5231R-ZE? I want to buy one of those too but I didn't see any comparison talk. I'm doing a new three cam setup, two in front and one in back of house.
Mr_D
Getting comfortable
Email Andy directly at kingsecurity2014@163.com with your needs. He'll get back to you quickly with price and availability.
looney2ns
IPCT Contributor