Search results

i'll try that Thanks

5.2.4.3 It did it again last night only difference was at 11:16 PM then it put 8:30 AM as 2nd photo

I have cameras set up to send me 10 images by email for alerts. Last night i had an alert and 1st image was dark out, 2nd image showed a image during the day when sun was shinning then the rest were all at night. all the images were at 11:30 PM except the 2nd one in color shows 6:40 PM. Any...

I would run several cables and use the switches. I have 18 cameras on my house feeding thru 1 cat 6 cable about 130ft to my garage out back then it is connected to a switch with another 18 cameras and the BI machine in the garage with no issues.

For BI to tag as a recording Set up onvif in the camera with same user and password and then setup pullpoint subscriptions in BI and it will show the alert as onvif

That helped it was there was no db after blue iris somehow it was gone. Thanks

I changed my hard drive out and copied everything over to the new one everything was working. After a few days the recordings stopped and I was only able to view a picture. When I went in found the storage drives full and once I deleted some clips it started recordings again. Again today noticed...

@bc99 They also have a 20 watt poe floodlight

Poe Ir PL-PoE-IR-6w PoE IR Illuminator ( mode B 24v ) with 802.3af passthru

Maybe this will work for powering 4 cams with poe https://www.amazon.com/dp/B0198H6EUK/?coliid=I1829D26JP3D7G&colid=2UUSBPH0PE5HF&psc=0&ref_=lv_ov_lig_dp_it

They have a board you can use on your own choice of lights. PL-POE-kit OEM PoE Conversion Kit

These are pass thru so you can use the camera cable PL-PoE-IR-6w PoE IR Illuminator ( mode B 24v ) with 802.3af passthru

You can get these pass thru PL-PoE-IR-6w PoE IR Illuminator ( mode B 24v ) with 802.3af passthru

I have found that the card disappears and a reboot or sometimes 2 it will show back up.

It's a toss up with ivs you have to set target ssizes properly or it'll trigger shadows. My ptz cams work with the Get events with PullPointSubscription But the domes I had to set up onvif to get some to work. Bi will show as an external alarm but sometimes it misses it

Some of the cameras will work with Get events with PullPointSubscription It depends on firmware best bet is to watch the videos on zone crossing and learn it. That works with any camera

It's for personal use. I started with BI with cheap 720 cameras. But night vision was only good for about 30ft cause there's no lighting around. When I found the Dahua starlight cams I started replacing them. Decided before I put the cams up I would put 64gb cards in them and learned the ivs...

I have BI recording 24/7 and zone crossing setup for alerts. Then the Dahua cams i set up the ivs to record to the memory cards in the cameras. Then i also setup a Dahua Nvr recording 24/7. I have almost 30 cams and should have a total of 3 recordings for an event if needed

@EMPIRETECANDY it's IPC-HDW4231EM-AS

There was something about newer being signed so you can't go back

Yes from Andy, but read that you can't go back on firmware easily

I seen it some where here some one posted. If I only had few cams wouldn't hurt it's because 20+ Here's pics of cam setting on all streams and bi for same cam at 30 It's address 150 1st substream is for smart pss app 2nd substream not even enabled

That's my problem No matter what you set the Cams for they do 30 fps. Except for the ptz and varifocals. Here's pic of BI staus page. No matter what they are set for in the cameras they show 30 8n Bi

Yes i have to use "Limit decoding unless required" I have 20+ cameras and all are Dahua so all the dome cams i can't set the fps. I set them to 15 in the camera but there stuck at 30 with BI. If i turn off "Limit decoding unless required" on the cams i have on cpu goes to 100 Cause of the...

I have been having BI tools sending me emails and rebooting BI cause cpu going to 100% and have been trying all the memory leak drivers. I found out if i leave the ui3 open on a computer is what's causing the cpu to climb to 100% so that it gets rebooted. Within few minutes of opening ui3 the...

try turning smart codec off

what are the min & max settings? for the target filter Looks like you need to try adjusting them

why not use this PL-PoE-IR-6w PoE IR Illuminator ( mode B 24v ) with 802.3af passthru there's a few different models i have there regular motion sensor lights. the model i have uses the same cable for the camera and powers both

Is there an easy way to change firmware backwards? I have 28 Dahua cams on Blue Iris and it locked up today. I have all the cams set at 15 fps but seems that the fps bug is happening to every cam i have except the PTZ's. There all a mix of 5231, 4231's every one of them says there running...

@catcamstar with dahua cams my nvr pushes the ivs to the cam (can see directly thru the cam web page) but the nvr will let me do ivs with other manufacturers so those must work thru the nvr.