Mini PTZ v2: 4x optical zoom version

bob2701 said:
Here are a few nite images, first 2 are the same as the day images earlier and then a swing around to catch the front steps. Front steps have added light from front door.
Click to expand...

Do you have anything to point at in the dark that would require zooming out. For example, a building across the street?

Thanks for sharing!
 
Promod117 said:
Do you have anything to point at in the dark that would require zooming out. For example, a building across the street?

Thanks for sharing!
Click to expand...

Remember, this is a 4X, the first picture is the driveway at 1X and the second is the mailbox at the end of the drive at 4X. Trees on both sides prevent shooting at a house nearby.

This is the lot next door and it is pitch black.

Side yard pich black.JPG
 
Last edited by a moderator:
  • Like
Reactions: ilrider78 and Promod117
Looks good. Thanks for sharing
 
Yes, so far so good. 1000 % better than the original V2 4X.

I had asked Jack about the new firmware and here is his reply.

IPNC_S2l2.0.1_build201607221508 this is 10X update


4X Please do not update.
 
bob2701 said:
Yes, so far so good. 1000 % better than the original V2 4X.

I had asked Jack about the new firmware and here is his reply.

IPNC_S2l2.0.1_build201607221508 this is 10X update


4X Please do not update.
Click to expand...
Oh, interesting, in the past same firmware applied to both cams
 
The night images look very good. But now it has external PoE and my junction box is too small to house it. Do you have the dimension of the PoE splitter? Thanks.
 
Futaba said:
The night images look very good. But now it has external PoE and my junction box is too small to house it. Do you have the dimension of the PoE splitter? Thanks.
Click to expand...

I did not measure it before installing but it is close to 4" + the weatherproof cable connector adds another 1 1/2. This is why I used it to enter the soffet instead of the short section of pipe from the other camera, see post #389.

Also with the external POE you want to disconnect from your POE switch before plugging in the camera. I changed the plate on the box today and just unplugged the camera to change it, when I reconnected it it would not sync up correctly. No PTZ and none of the presets worked. Unplugged from the switch, waited 10 minutes, plugged in again and all was good. Not sure if there is a correct connect sequence, power first or network first. By connecting or disconnecting at the switch there is no problem.

All in all I am very happy with this camera.
 
Late to the 400+ thread here, compatible with which NVR recorders like hikvision or Dahua or this one a totally over the local LAN and try to get at it from the NVR from the outside the NVR LAN?
 
arw01 said:
Late to the 400+ thread here, compatible with which NVR recorders like hikvision or Dahua or this one a totally over the local LAN and try to get at it from the NVR from the outside the NVR LAN?
Click to expand...

If you're too lazy to read the 2nd page of posts then you shouldn't be buying this.

klasipca said:
Also to me the main advantage of Huisun/Imporx it uses Hikvision protocols.
Click to expand...
 
bob2701 said:
Yes, so far so good. 1000 % better than the original V2 4X.
Click to expand...
Have you tried comparing 10x with 4x? In terms of IR output?
 
klasipca said:
Have you tried comparing 10x with 4x? In terms of IR output?
Click to expand...

I did not compare before installing but they seem to be about the same. Right now I have the 4 in the front of the house and 2 10's in the rear. No way to do a real comparison but they look close. Each side has the older 3x and they look just as good.
 
  • Like
Reactions: klasipca
bob2701 said:
I did not compare before installing but they seem to be about the same. Right now I have the 4 in the front of the house and 2 10's in the rear. No way to do a real comparison but they look close. Each side has the older 3x and they look just as good.
Click to expand...
wow, now you have more of them then I do, aren't you afraid of owning so much junk? ))
 
Enjoying my cheap junk!

b1ef626ed51c4e424113ed07736f4abd.jpg


Sent from my Nexus 6 using Tapatalk
 
  • Like
Reactions: ilrider78, klasipca and alastairstevenson
gpower07 said:
any firmware update for the v1??
Click to expand...
is your "v1" with s2l or a5s? You can check with batch tool as I recall they started putting new chipset a while back. If it's s2l then you will likely be able to upgrade using the same v2 firmware.
 
hello bob2701
How long did your camera took to arrive at you house.
Regards.
Chewie
 
You must log in or register to reply here.
Top Bottom