tommyd75
Young grasshopper
- Jan 30, 2016
- 43
- 13
I just ordered this also. Which firmware did you load onto it for rtsp support ?
Sent from my iPhone using Tapatalk
New RCA HSDB2A 3MP Doorbell IP Camera
- Thread starter fleece
- Start date
I just ordered this also. Which firmware did you load onto it for rtsp support ?
Sent from my iPhone using Tapatalk
The ezviz version works with rtsp out of the box. At least mine did when updated to the latest firmware(I didn’t try to connect before I upgraded it.)
Last edited:
So can you tell us which firmware (build) version your EZVIZ is using? Does ONVIF work? Thanks
Also my thoughts about transformer. Our 16v 10va also worked but my thought was since I will be running two RTSP 24/7 streams I would just upgrade to a 16v 30va.
All the firmwares support RSTP (right out of the box), it is we found LaView and Nelly's only support ONVIF.
A tip for new owners:
The default FPS is 15, to get 30FPS in iVMS-4200 software or the Batch Configuration Tool you can change the Frame Rate: to Full Frame (which is 30FPS)
The default FPS is 15, to get 30FPS in iVMS-4200 software or the Batch Configuration Tool you can change the Frame Rate: to Full Frame (which is 30FPS)
Last edited:
My unit is scheduled to arrive tomorrow/Sunday, and there's an 80% chance of rain all day. Thankfully, my doorbell is beneath a covered front porch. Question for the latest installers here: Does this come with an L-shaped Torx driver? I seem to have misplaced my original one from three years ago. 
This is what you get, this is the RCA but same hardware in All boxes but different face plates depending on brand.My unit is scheduled to arrive tomorrow/Sunday, and there's an 80% chance of rain all day. Thankfully, my doorbell is beneath a covered front porch. Question for the latest installers here: Does this come with an L-shaped Torx driver? I seem to have misplaced my original one from three years ago.
Thank you for that image, David. I may just have to drill out the old security Torx screw, then. If I recall, it's tapered so a regular torx bit just won't fit it.
Ok I just went and grabbed my tool, pulled out my tool?, haha no right way to say it haha, on one end it has the Torx for the security screws. Was hoping to find a T number to tell you. I grabbed my bit set and the lowest it goes is T8. By looking at the Screwdriver/Torx tool that comes with the Doorbell it is either a T6, T5 or T4, just guessing. Hope this helps...Thank you for that image, David. I may just have to drill out the old security Torx screw, then. If I recall, it's tapered so a regular torx bit just won't fit it.
UPDATE: Oh now I see what you mean about tapered...Dang I better not lose this tool...
Was looking at this set:
Last edited:
As an Amazon Associate IPCamTalk earns from qualifying purchases.
Hello guys, justjoined here and I am excited in my hunt for the best door bell which can record to nvr like synology nas without much hassel.
I see some here mention DB2 is that the RCA hsdb2a or Laview one halo? Is that better than ezdb1? I am so confused their prices are all very same.
Also have some.people here flashed the ezdb1 to laview one halo firmware??
Appreciate your guidance thanks!
I see some here mention DB2 is that the RCA hsdb2a or Laview one halo? Is that better than ezdb1? I am so confused their prices are all very same.
Also have some.people here flashed the ezdb1 to laview one halo firmware??
Appreciate your guidance thanks!
They are all the same except for the face plate covers. EZVIZ right now has the best price.
As an Amazon Associate IPCamTalk earns from qualifying purchases.
Thanks David, but someone on slickdeals mentioned this about the 90$ ezdb doorbell, their quote below
----!----
This is the first version of the db2 sold as Nelly's Security Doorbell or Laview security Doorbell. I don't believe that the DB1 is supposed to get new firmware moving forward, so I'd shoot for the DB2 if you want to go that route. But I've read that some people had issues with them. I might get both, start with the DB 2 and if that fails, return it and try the Eufy. Otherwise return the Eufy. I do really want ONVIF
____!-----
Is the above true or maybe they did not flash the laview firmware? Does the ezdb1 come with 3 color faceplates or we gotta paint? I thought the halo 1 wS much better than the ezdb1 as thars 1st gen and heard the LaView 1st gen was super crap per reviews online.
As an Amazon Associate IPCamTalk earns from qualifying purchases.
These are all Hikvision Doorbells. I bought the LaView, it only came with white face plate. Not sure about EZVIZ but there a some very recent users on this forum who has bought/ordered EZVIZ who you can ask.
The above post is wrong, we have seen new firmware come out. When I bought my LaView it did not have ONVIF support, but now it does.
So basically there are two Hikvision Doorbells, the older one is: I have no experience with the first gen.
What we found is you can load the firmware from the different brands and so far LaView and Nelly's support ONVIF. Each brand has their own model number but again they are all the same hardware.
The Second Gen looks like this:
Last edited:
David did you buy the laview halo 1?
Is the halo one same spec wise to RCA hsdb2a? Price wise they are almost same..
Cheapest one is the ezviz db1 but for sure it is lower spec than the one you have and the hsdb2a? As its db1?? Or they are ALL same hard ware spec but just clones??
Thanks!
They are all the same Hikvision camera, same specs, same box. Only difference is face plate colors and firmware (which is not a problem since you can load any firmware from either brand) Yes I have the ONE Halo.
I've had the first-gen Hikvision (the LTS variant) for over three years now. It's still available for a higher price at Amazon.
As an Amazon Associate IPCamTalk earns from qualifying purchases.
I've been running the RCA HSDB2A variant since January and waited a long time for the updated FW to enable ONVIF. I thought that it was the previous outdated RCA FW that didn't allow the "Alexa, show me the front door" live feed integration. After running the latest LaView ONVIF V5.2.4 build 190716 FW for a couple of months now, I still can't get the doorbell to show up in Alexa discover devices process. Wondering if it might be my unit even though everything else has been running fine since I installed it in January. I have Image Encryption disabled for the doorbell and have it registered in the Ezviz app currently. If others have it working with Alexa, I may talk to RCA support to get it looked at under warranty before it expires in mid-January. I have a couple Echo Show 8's coming from Amazon from Black Friday deal and want to be able to "show front door" from kitchen/etc instead of sometimes delayed video call notification on cell phones. Other Ezviz compatible cameras show up in Alexa app except for my RCA LaView FW doorbell.
Has anyone who has the RCA HSDB2A variant configured it successfully with Alexa? If so, where is the doorbell registered to(Ezviz, RCA, Hik-Connect, LaView ONE app) and any extra tweaks beyond the standard directions?
1. From the EZVIZ Mobile App, select a suitable name for your camera (i.e., baby room, front door, etc.)
2. From the EZVIZ Mobile App, disable Image Encryption for the camera you wish to setup
3. From your Alexa App, search for EZVIZ, enable the skill and link it to your EZVIZ account by signing in with your EZVIZ account
4. Discover your cameras by asking Alexa “Discover devices” or by pressing the Discover Devices button in the Alexa app
Once your account is linked, viewing your cameras is supported on Amazon Echo Show, Echo Spot, Fire TV, 2nd Gen Fire Stick or Fire Tablets (7th gen and above). To see your camera, just say “Alexa, show the (camera name)”
Has anyone who has the RCA HSDB2A variant configured it successfully with Alexa? If so, where is the doorbell registered to(Ezviz, RCA, Hik-Connect, LaView ONE app) and any extra tweaks beyond the standard directions?
1. From the EZVIZ Mobile App, select a suitable name for your camera (i.e., baby room, front door, etc.)
2. From the EZVIZ Mobile App, disable Image Encryption for the camera you wish to setup
3. From your Alexa App, search for EZVIZ, enable the skill and link it to your EZVIZ account by signing in with your EZVIZ account
4. Discover your cameras by asking Alexa “Discover devices” or by pressing the Discover Devices button in the Alexa app
Once your account is linked, viewing your cameras is supported on Amazon Echo Show, Echo Spot, Fire TV, 2nd Gen Fire Stick or Fire Tablets (7th gen and above). To see your camera, just say “Alexa, show the (camera name)”
According to the app this is the latest FW from EZVIZ.
I am unsure if ONVIF works. I would think that it does not, as I am not getting anything in Blue Iris(besides a video stream.) Is there a good was to test ONVIF?
As far as the faceplates go, the EZVIZ camera does come with multiple faceplates along with all the hardware just the same as the others. The Amazon listing shows this.
Last edited:
Yes. I purchased from amazon:
As an Amazon Associate IPCamTalk earns from qualifying purchases.