No...the camera will be fed by a POE switch on the side of the road that has the receiving transmitter, which will also be fed by the same POE switch....
Point to Point Wireless Bridge Recomendations
- Thread starter jwadsley
- Start date
tangent
IPCT Contributor
- May 12, 2016
- 4,612
- 3,968
There is a building with power between where the pole will be for the receiving transmitter and where the camera will be. Both camera and receiver will connect via RJ45 to the POE switch and get power. The main issue I'm having is getting from the NVR to the far out camera, because I have to cross a road.
I second this. I have used Mikrotik for 20+ years in -45 cold climate on 140' towers and they have never let me down. I still have some units that are 15+ years old and they still work. At this point I wouldn't consider anything else because you can get a full Mikrotik 5GHZ AC link for $100.00
Ya, would love to see this amazing gadget...Can you provide a "link" to the "link" ?
That's great!
I likely got your situation crossed with someone else's, as there has been a LOT of posts regarding such links in the past week.
Can you provide a "link" to the "link" ?
Mikrotik SXTsq 5 AC. Just a quick search, and its probably gone up in price a bit, but it is listed at $65 per radio on their site. There are many resellers available in all countries so finding them is fairly easy.
MikroTik
MikroTik makes networking hardware and software, which is used in nearly all countries of the world. Our mission is to make existing Internet technologies faster, more powerful and affordable to wider range of users.
mikrotik.com
SXTsq 5 ac | MikroTik
Low-cost small-size 16dBi 5GHz dual chain integrated CPE/Backbone with AC support and Gigabit Ethernet
mikrotik.com
You need two per PTP link. One is setup as an AP bridge and the other is a bridge. If you have line of sight as in a clear fresnel zone you should be able to get ~300Mbits/sec with a link like this. It comes with a POE injector as it does not conform to the 802.3af standard. If you need more throughput there are other options on the site. You should be able to get a few miles out of this link if needed, but it is fairly small and compact so one with a larger antenna would be required if you want to go 10-20 miles.
Thanks!Mikrotik SXTsq 5 AC. Just a quick search, and its probably gone up in price a bit, but it is listed at $65 per radio on their site. There are many resellers available in all countries so finding them is fairly easy.
MikroTik
MikroTik makes networking hardware and software, which is used in nearly all countries of the world. Our mission is to make existing Internet technologies faster, more powerful and affordable to wider range of users.SXTsq 5 ac | MikroTik
Low-cost small-size 16dBi 5GHz dual chain integrated CPE/Backbone with AC support and Gigabit Ethernet
You need two per PTP link. One is setup as an AP bridge and the other is a bridge. If you have line of sight as in a clear fresnel zone you should be able to get ~300Mbits/sec with a link like this. It comes with a POE injector as it does not conform to the 802.3af standard. If you need more throughput there are other options on the site. You should be able to get a few miles out of this link if needed, but it is fairly small and compact so one with a larger antenna would be required if you want to go 10-20 miles.
Nice alternative to Ubiquiti for now, as they are scarce and pricey....I hope that's temporary. I may just try a pair on my next link that I need for someone (waiting for phone to ring).
Not too thrilled about the form factor of the POE injector and wall wart for power, though (image at bottom)...reminds me of some earlier Engenius and TP-LINK gear. But it's likely pins 4/5 for positive and 7/8 for negative since it's passive, I've got a dozen Ubiquiti 18 and 24VDC POE injectors laying around.
It seems they'll squeeze another $3 out of you for a pole mount, several competitors make that provision in the design of the radio. It's not a deal breaker certainly so I'll definitely try a pair next go-round.
Thanks!
Nice alternative to Ubiquiti for now, as they are scarce and pricey....I hope that's temporary. I may just try a pair on my next link that I need for someone (waiting for phone to ring).
Not too thrilled about the form factor of the POE injector and wall wart for power, though (image at bottom)...reminds me of some earlier Engenius and TP-LINK gear. But it's likely pins 4/5 for positive and 7/8 for negative since it's passive, I've got a dozen Ubiquiti 18 and 24VDC POE injectors laying around.
It seems they'll squeeze another $3 out of you for a pole mount, several competitors make that provision in the design of the radio. It's not a deal breaker certainly so I'll definitely try a pair next go-round.
View attachment 159189
Yes, I don't like the injectors, but they work. I have in the past used a coupler on the RJ45 end and extended it with a patch cable so that it can all be hidden in a rack or cabinet somewhere behind everything else and the patch cable is nicely routed in the cable management brackets. There are some models that support POE and POE+ as power sources, but for some reason the higher power radios are still passive. You don't need the pole mount. There are slots in the plastic housing that accept a pipe clamp if the $3 is over your budget. I never bought any, I just used the pipe clamps that came with it or whatever I had lying around and old satellite mounts. The bigger radios and antennas come with proper mounting gear. The goal of Mikrotik's products is to make them affordable, so sometimes options are slim.
tangent
IPCT Contributor
- May 12, 2016
- 4,612
- 3,968
Does this building have it's own electric meter or is the power fed from the main structure on the other side of the road?
No worries. Just wanted to confirm that I'm looking for standard POE 802.11F or whatever the standard is so that I don't need a power injector at the point of transmission, I can run it from a POE NVR.That's great!
I likely got your situation crossed with someone else's, as there has been a LOT of posts regarding such links in the past week.
Sounds like Mikrotik SXTsq 5 AC wouldn't work for me, but would the ones you suggested?
I don't see why not....just remember they use a 24VDC pasive POE injector (included).
yes.
EDIT 4/5/23 @ 1353 CT: to get the best through-put, speed, reliability and the rest of the desirable attributes, you use a pair of the units of the same make and model, regardless of who makes them, as they generally employ some proprietary protocal as they communicate which works so much better than run-of-the-mill W-Fi. All of them have their names for such techniques which are software-based for the most part, some may be better than others, I don't know....I've been pleased with Ubiquiti gear so haven't felt the need to look elsewhere.
Last edited:
Trying to keep it as simple as possible. If I can use standard POE protocol and only need one cable connected from the transmitter and receiver to a POE type switch, then that simplifies things greatly...
I spent about 15 minutes looking for Ubiquiti, Mikrotik, Engenius and TP-LINK outdoor, PtP AP/bridges that did NOT use either 24VDC passive or "proprietary" 54 volt power injectors and came up empty handed. Engenius specs may be the closest but they are ambiguous, stating "proprietary" and "54 volt" in one part of specs but mentioning compatibality with POE cameras and switches in another.....so it's unclear. Sorry I cannot be of more help in that regard.
Could be why the 802.3af POE-to-24VDC adapter came about.
Could be why the 802.3af POE-to-24VDC adapter came about.
No worries at all, you have been very helpful.I spent about 15 minutes looking for Ubiquiti, Mikrotik, Engenius and TP-LINK outdoor, PtP AP/bridges that did NOT use either 24VDC passive or "proprietary" 54 volt power injectors and came up empty handed. Engenius specs may be the closest but they are ambiguous, stating "proprietary" and "54 volt" in one part of specs but mentioning compatibality with POE cameras and switches in another.....so it's unclear. Sorry I cannot be of more help in that regard.
Could be why the 802.3af POE-to-24VDC adapter came about.
Was hoping to get a standard 808.3af so I could just plug in a POE cable and be good to go, but doesn't look like that is the case
