Review-I'll be the guinea pig for the new SD59225U-HNI PTZ.
- Thread starter looney2ns
- Start date
Larebear
Pulling my weight
You are right ljw2k. It's still not sitting at a true 90 degree's. The shims helped some but it would take quite a few more to make it square. For me it's more of a temporary mount until there's a better solution. It's mounted under my deck cover, so I'm not too worried about the elements causing problems. Snow and rain can't get to it. Hopefully Andy will come up with an acceptable solution for all of us.
hmjgriffon
Known around here
Larebear
Pulling my weight
It does look like it's still off, even with the shim which is about 1/2" (13mm) thick. Strange thing is that it looks square with the side of my house in this snapshot.
I know this is a half arsed solution but why not use mount DH-PFB303W?
As it's the same pipe thread and diameter and for me looks better?
I've asked Andy if he can send that mount out instead on the one that's included.
He may not be able to but it's worth asking
As it's the same pipe thread and diameter and for me looks better?
I've asked Andy if he can send that mount out instead on the one that's included.
He may not be able to but it's worth asking
PFB303 not suits, i booked some new ones today, and will see if it's good. We told dahua engineer this mistake, seems they still don't have a direct response for this.
wantafastz28
Getting comfortable
Wow, mine was off, but nothing like that... odd they have different amounts of tilt.
wantafastz28
Getting comfortable
I see what you're saying now... mine was nothing close to that. I wish I had a smart level when I mounted mine to see the exact degree... I bought a few washers since the bubble made it look really bad, but only used a pair.
Solar Deity
Getting comfortable
Mine arrived last night and I have the same issue with the bracket, but I'm far from upset.
I'll gladly accept a new one, but can make this work without much issue. With my keen eye, I would say it's 15 degrees from plumb. It is square though.
I don't want a separate shipment for the bracket. Just send it with my next order.......
Pic isn't the perfect angle, but you can tell.
That being said, this camera is amazing!
SD
I'll gladly accept a new one, but can make this work without much issue. With my keen eye, I would say it's 15 degrees from plumb. It is square though.
I don't want a separate shipment for the bracket. Just send it with my next order.......
Pic isn't the perfect angle, but you can tell.
That being said, this camera is amazing!
SD
Attachments
So, why doesn't Dahua make some sort of adapter/bracket/mount that adjusts just like the 5231 turret? If would allow you to mount to siding that's at an angle, and still be able to adjust the camera to level it. Like a ball and socket swivel assembly. It would sure solve alot of problems. The current mount is pretty archaic to me, with problems like this.
Solar Deity
Getting comfortable
hmjgriffon
Known around here
So I am now wondering if no one ever checks these, mine is off exactly 1/4" at the wide end. I'll shoot Andy a message, I'd rather have the PFB303W also.
handinpalm
Getting comfortable
Here is a quantitative measure on how far my supplied mount is off and how I mounted it. The board I am measuring from is completely plumb, then I pulled the top of the mount away from the board until the camera mount end is completely level. I measured 0.60" (~15mm) where the top mounting holes are. Meaning you need a standoff or shim a little over 1/2 inch behind the top mounting holes. The mounting is a Kludge because of the wrong bend in the pipe, but my installation is pretty high up and not that noticeable. I am very impressed with the zoom video with this Cam. Thanks Loony2ns for posting this thread and many thanks for everyone who contributes to IPCT, especially Nayer! Still waiting for varifocal starlights.
I added some weatherstripping in a stepped mannor to cover the gap from Insects.
This is what I used for standoffs for the top mounting holes.
I bent the supplied cable inside the mounting tube to take up the slack. Probably exceeded the minimum bend radius, but it is what it is.
Mounted on house>
I added some weatherstripping in a stepped mannor to cover the gap from Insects.
This is what I used for standoffs for the top mounting holes.
I bent the supplied cable inside the mounting tube to take up the slack. Probably exceeded the minimum bend radius, but it is what it is.
Mounted on house>
Last edited:
handinpalm
Getting comfortable
BTW, I do not think anyone has described the IR lights on this model yet. There are 4 IR LEDs. 2 normal ones and 2 high power ones for the far zoom applications. When zoomed in, all 4 LEDs are on. They work very well for the far zoom video. I am amazed how well I can see at distances in the dark.
Last edited:
hmjgriffon
Known around here
Good job, awesome house, tampa/st. pete area is one of the ones I am considering moving to.
ypl
Getting the hang of it
I got mine today. I just connected it to check if it works and all looks fine - it works, makes some disturbing constant noise and I can see the image in the browser plugin. I cannot evaluate the image quality because it is just test run and it lies on the floor of my lounge room so I'll give you some feedback when I attach it to the wall. I checked the wallmount and it looks like it's bended but I am happy to try to mount it to the wall. If I fail I'll ask Andy for a straight wallmount with my next order but probably the bended one will do the job. Overall I can truelly recommend Andy. He quickly replies, answers all the questions, allows to pay via paypal or via aliex, ships via quick or no tax route (tested and works for Poland). Definitelly I will order more stuff from Andy, I just need to figure out what I need. I just build it for fun around my house.
Attachments
hmjgriffon
Known around here
n0xlf
Getting the hang of it
- Jan 19, 2017
- 59
- 38
Funny you mention that - I almost thought of a test install to see if they were compensating for some sort of lens distortion or something. I doubt it, but...