Setting up Zmodo ZP-IBH13-w

[shaba]

Done
Now i see, image don't move for several seconds and then starts again
I have cam connecterd with lan cables and wifi disabled
Can you give me you full setting?
Thanks

 

[fenderman]

Done
Now i see, image don't move for several seconds and then starts again
I have cam connecterd with lan cables and wifi disabled
Can you give me you full setting?
Thanks

Did you uncheck the box for the rtsp timecode?

 

[shaba]

This is my conf.
I'm testing it, it seems it works better now!
Let me see.. :hope: )(

 

[shaba]

In seems it works!
only 1 disconnect during capture in 2 days
Thanks!

 

[fenderman]

In seems it works!
only 1 disconnect during capture in 2 days
Thanks!

to minimize disconnects increase the receive buffer to 20mb

 

[Sparky1996]

Please excuse me, as I am very new to this, this is actually the first IP camera I have purchased, and it is fighting me.... It could certainly be something simple, but I think I have input everything correctly and I still cant get this to show up in BI, it shows fine in Zmodo software. I updated the camera firmware, and BI is the lates version, please help I have been at this for hours with no success.

 

[djangel]

The attachment posted show the parameters results from using the Find/Inspect button?

 

[Sparky1996]

No that's How I tried to set it up from reading all the posts I could find here on Zmodo/Funlux
Attached I what the result of the Find/Inspect

 

[djangel]

Try entering the camera IP address and port in the address entry and retry Find/Inspect

camipaddress:10800

 

[djangel]

Also try

camipaddress:10554

 

[djangel]

If it doesn't work, probably need to access the cam web page and check some settings. Check the RTSP feed first and make sure is enabled.

 

[Sparky1996]

Where is camiaddress at?
Thanks

 

[djangel]

Where is camiaddress at?
Thanks

Your cam IP. What did you set it to? Connect to the cam via the Zmodo app and check the network settings. Could be that your cam is set for dhcp, unless of course you set a static IP for it.

Also, I was reading real quick over the user manual and the default video port is set for 8000, so try "your cam's IP address", for example, 192.168.0.100:8000

 

[Sparky1996]

IN the video Code of the camera when I log in on the web Browser I only see options for
Stream
-VBR
-CBR

 

[Sparky1996]

I do have DHCP enabled, but in the router I have the address reserved
I tried 8000 and that did not work

 

[djangel]

Are you using wifi? What is your cam's FPS set to? 30fps?

 

[Sparky1996]

I am using WIFI, this camera has no other connection (No Cat-5)

I have tries all kinds of frame rates, problem is every time it has the same result when performing the find/insect, it says RTSP Port OPEN? as if it can not locate it.

 

[fenderman]

I am using WIFI, this camera has no other connection (No Cat-5)

I have tries all kinds of frame rates, problem is every time it has the same result when performing the find/insect, it says RTSP Port OPEN? as if it can not locate it.

Dont use find inspect...enter the correct url under the generic rtsp option.

 

[rdshackleford]

to minimize disconnects increase the receive buffer to 20mb

Would you recommend that for all camera types, not just this Zmodo?

 

[Sparky1996]

So after calling Zmodo, the new camera's do not support ONVIF, so it seemed no matter what I would do it would not work. I ended up just purchasing the NVR, and in minutes everything was up and running. Kind of upsetting that you can't use 3rd party apps, but it all works well now, and was very simple.