That .bin doesn't look like I can download it anywhere? Or is that a line on how to get it?
Dahua Mini Black Face PTZ (SD29204S-GN & SD29204T-GN)
- Thread starter nayr
- Start date
hmjgriffon
Known around here
No luck. The file did upload fine but the same problem is still occuring every 3.5 minutes.
DH has Dahua Branding, General is unbranded..
same thing w/model numbers.. if you get a DH-IPC or DH-SD it'll have a Dahua logo on it.. if you get just an IPC/SD model it'll be a whitebox model w/no branding.
same thing w/model numbers.. if you get a DH-IPC or DH-SD it'll have a Dahua logo on it.. if you get just an IPC/SD model it'll be a whitebox model w/no branding.
This one took and fixed the zooming problem but downgraded the picture quality and interface a lot. I have attached a picture from a good cam vs the firmware just updated. At least it's good to know once we have the right firmware I think the solution will be fixed. Good one obviously has the better lighting and definition.
reset it to defaults, looks like its running a higher shutter speed or really low gain.. you might need to tweak em after updating em to get em back to where you had em.
Getting closer, thanks. Still needs a little work on the definition. Good camera is much clearer. We have someone trying to pull a firmware from a good camera later tonight. That way we can have the exact firmware and just upload the same config file to all of them. The different firmware won't accept the config file from other cameras of course.
Thanks for all your help nayr.
check the bitrate; looks like its very low bitrate right now..
yeah this firmware has alot of new shit in it, you may consider updating all of them to this and making a new configuration file.. here's the release notes: ftp://ftp.asm.cz/Dahua/kamerove_systemy/_Firmware/05SD/Main_Firmware/02-the%20latest%20firmware_2016.11.11/Introduction%20to%20V2.422%20Firmware.pdf
It has some new overlay options you might find attractive for your broadcasts perhaps.. the interface was not downgraded, it was upgraded.. might look a bit different but all the old features are still there but new configurations are now available.
I was unable to locate the firmware you were running before
yeah this firmware has alot of new shit in it, you may consider updating all of them to this and making a new configuration file.. here's the release notes: ftp://ftp.asm.cz/Dahua/kamerove_systemy/_Firmware/05SD/Main_Firmware/02-the%20latest%20firmware_2016.11.11/Introduction%20to%20V2.422%20Firmware.pdf
It has some new overlay options you might find attractive for your broadcasts perhaps.. the interface was not downgraded, it was upgraded.. might look a bit different but all the old features are still there but new configurations are now available.
I was unable to locate the firmware you were running before
Last edited:
Thanks for checking on the firmware. The bitrates are the same in all photos. I have all cameras changed down to 25 fps and 1024 kbps for bitrate. This allows a smoother stream back to our server and we can usually keep a smooth stream to our viewers with these settings.
Soooo,
I KNOW this is not an outdoor \ waterproof camera. Yet the idiot in me really wants to use it in a spot, 2nd floor under the eve of my house where it would be very handy.
It would be North-ish facing which where I'm situated blowing winds\rain usually comes in from the Southwest so it should not get straight on rain running down it and typically would be protected from the wind blowing anything into it.
That said, nature does blow stuff any which way sometimes so no guarantees.
I mean would something like high humidity or temp changes cause condensation that could fry it?
Are there any suggested waterproofing steps I could take to help ensure it would work properly outside?
Foam baffle trim mounting ring, silicone etc.?
...Or am I just asking for trouble having this outside at all?
I KNOW this is not an outdoor \ waterproof camera. Yet the idiot in me really wants to use it in a spot, 2nd floor under the eve of my house where it would be very handy.
It would be North-ish facing which where I'm situated blowing winds\rain usually comes in from the Southwest so it should not get straight on rain running down it and typically would be protected from the wind blowing anything into it.
That said, nature does blow stuff any which way sometimes so no guarantees.
I mean would something like high humidity or temp changes cause condensation that could fry it?
Are there any suggested waterproofing steps I could take to help ensure it would work properly outside?
Foam baffle trim mounting ring, silicone etc.?
...Or am I just asking for trouble having this outside at all?
at least one person has pole mounted this fully exposed and as far as I know it still survives.. I dont think anyoe's killed one of these yet outdoors, other than potentially toasting the microphone.. YMMV and your rolling the dice since you know that this is not an outdoor camera
Thanks.
I'll take a chance then and follow up after spring rains hit and hope I still have a cam.
If anyone else...or that one guy is out there reading this...Please let me know your experience with this indoor cam used outdoors exposed.
That new <$400 PTZ is sounding interesting though too (SD49225T-HN thread).
I'm waiting to see more discussion \ samples \ reviews on that.
hmjgriffon
Known around here
Look at he starlight turret, and then imagine it with pan, tilt, and lots of zoom lol.
my ptz has been working well
i half ass setup semi-auto-tracking with presets its been firing off like nothing
hmjgriffon
Known around here
Can you give a brief walkthrough? I was confused by some of the settings when I was trying to set it up.