Looking for opinions on my options for LPR install locations.

I wonder if it might stop while using a 12v 1.2 or 2.0 amp wall wart?
 
  • Like
Reactions: sebastiantombs
Flintstone61 said:
I wonder if it might stop while using a 12v 1.2 or 2.0 amp wall wart?
Click to expand...
If that works, then it probably means the cam has a problem, not the network.
 
  • Like
Reactions: Flintstone61
I emailed Andy, hopefully he will be able to help me with some direction.

I'm also a bit bummed that Fall Break is over and I will be going back to work tomorrow. I got a lot done with getting these installed and set up over the last week, but would have liked a couple more days to have messed with them.
 
  • Like
Reactions: samplenhold, Flintstone61 and sebastiantombs
If no joy with Empiretech could he use one of them thar fancy pants thinga-mabobs you pluginto the end of the cable and convert/adapt the POE voltage to the 12VDC plugin voltage?
 
  • Like
Reactions: sebastiantombs
As an Amazon Associate IPCamTalk earns from qualifying purchases.
  • Like
Reactions: samplenhold and Flintstone61
Just watch the load on the power supply and what the voltage drop might be on the cable supplying the IRs and camera.
 
  • Like
Reactions: Flintstone61
sebastiantombs said:
Just watch the load on the power supply and what the voltage drop might be on the cable supplying the IRs and camera.
Click to expand...
Yea, I would be running a dedicated line to the camera if I went this route. It's a 5a power supply with 40w of IRs on it right now. I should be fine adding this, but would possibly go a little bigger if I added it.
 
I'd go a little bigger. You'll be at four, plus/minus, amps with a camera added to it. I like "headroom" of 50% minimum but you may feel differently.
 
  • Like
Reactions: Ri22o
I am finally getting back to working on my LPRs and can't figure out what the issue is with not getting consistent captures of the car/plate within the frame. Or why it takes shots of the front of cars with no license plate.

This is what I am wanting to happen, let me know if it is possible:
  • BI detects motion in the FOV and sends the image to CP.AI.
  • CP.AI verifies there is a plate in the frame and posts the image as an alert.
  • The license plate information is burnt onto the image, file name, etc.

Below is what I am getting, and most of the blank captures were triggered by a plate but this is what UI3 is displaying.

1680984121903.png


These are my settings and I have ALPR turned on in Global Settings.

338588545_138069959229640_443296586292553308_n.png

339405085_1440794119999361_2819185083342189649_n.png

338514034_552519730199738_3513957692320998408_n.png

339402772_1641907866256711_6807423457963995095_n.png
 
Ri22o said:
I am finally getting back to working on my LPRs and can't figure out what the issue is with not getting consistent captures of the car/plate within the frame. Or why it takes shots of the front of cars with no license plate.

This is what I am wanting to happen, let me know if it is possible:
  • BI detects motion in the FOV and sends the image to CP.AI.
  • CP.AI verifies there is a plate in the frame and posts the image as an alert.
  • The license plate information is burnt onto the image, file name, etc.

Below is what I am getting, and most of the blank captures were triggered by a plate but this is what UI3 is displaying.

View attachment 159481


These are my settings and I have ALPR turned on in Global Settings.

View attachment 159483

View attachment 159485

View attachment 159482

View attachment 159484
Click to expand...
You need to setup a zone crossing also post your annalist details like the below screenshot

1680989373279.png

1680989515216.png
 
It appears I did not have the LP module installed in CP.

My AI Analyze list is completely blank?
1680991844399.png

I am getting this in my Alerts.
1680991570275.png

And this in my Clips.
1680991612587.png
 
I clicked the button at the top of BI.

So, I had this issue before and completely forgot that the behavior is this way. I am trying to view all of this through UI3, but it does not present itself the same way as natively within BI.

If I click "Alerts" in UI3 I will get the video clips.
If I click "All Clips" in UI3 I will get some half-assed attempts at grabbing the plate.

If I click "Alerts" in BI I will get the entire list of alerts for all cameras and the stills I am looking for are buried in there. Is there a way to get them to populate in their own list or are they locked to the Alerts tab? Or to get them to work the same way in UI3?

1680993331924.png


Because you requested it.

1680993625108.png
 
I have them set up in separate groups, but I do not get a still capture of the license plate. I only get a 3 second video in Alerts or an absolutely non-useful still capture in All Clips.

Where do I find this image?

1680997002553.png
 
You must log in or register to reply here.
Top Bottom