San Diego, CAThis Sd8c845fg-hnf PTZ work at night, full color amazing! Any one know where it is?
View attachment 162615
Dahua WIZMIND X SERIES
- Thread starter EMPIRETECANDY
- Start date
This Sd8c845fg-hnf PTZ work at night, full color amazing! Any one know where it is?
View attachment 162615
San Diego Skyline.
Cool, the camera is for a touring watch for the bay, very nice, the full color camera is awesome!
Just to provide an example of what I wrote earlier, I looked up the specs of the SD8C845FG-HNF (nice San Diego skyline - although quite a bit of noise reduction in that image) and it says "Color: 0.0005 lux@F1.5" ... but because it's a BIG zoom (8 mm–360 mm), the Max. Aperture goes from F/1.5 to F/5.7. To be clear, this isn't specific to Dahua - it's just the laws of optics. Similarly, almost all moderate/super-zoom camera lens are also "variable aperture" - i.e. increases with zoom. Obviously the low-light capability will decrease with zoom.
Does anyone know if these be used to replace a current 5231-Z12E and capture license plates without OpenALPR? I wasn't sure if they came with onboard software or what could take care of the processing and storage of plates.
Those are ANPR cameras, but they have half the zoom of the Z12E so it may or may not work for you.
Parley
Known around here
The 8-32mm one might work if your camera is close to the street. I am in the process of rearranging some of my cameras and I will be using a 5442E-Z4E 8-32mm for a license plate camera. However, this one will be right next to the street. It will be replacing this one which is 2.7-12mm.
The 7 series is the smartest series right now, also support ANPR camera, not really to replace the Z12E,Z12E is cheaper and work great after you make DIY as a LPR camera.
If want a professional ANPR camera i stll recommend to use the ANPR special model IPC-LPR437B-IR.
Amazon.com : IPC-LPR437B-IR
As an Amazon Associate IPCamTalk earns from qualifying purchases.
That's really impressive @EMPIRETECANDY ... curious if the aperture/iris/F-Stop was held constant as it didn't appear that the light levels changed on the zoom in/out.
BTW, if you put that 1/1.2" sensor in a HDBW7442E1-Z4-X (less MP makes for bigger light sucking pixels) and want a tester, I'd love to have it watch my front lawn for the Internet to see! ;-)
BTW, if you put that 1/1.2" sensor in a HDBW7442E1-Z4-X (less MP makes for bigger light sucking pixels) and want a tester, I'd love to have it watch my front lawn for the Internet to see! ;-)
Last edited:
1/1.2cmos if no US ban i think dahua/hikvision will use a lot on their high end products, right now they find replacement on the market. You see the camera tech not too big progress since 2021, have some new things but all are very expensive. At today's economy situation across the world, expensive things not easy to sell, so can't be big volume.
Just to follow up from my previous post - there is a tantalising section of the release notes for the only firmware available for the camera, which is the same version it has shipped with. I have attached it. It seems to imply I should be able to have a higher frame rate available on both the Main Stream and Sub Stream 1, but whatever I do I can't get the sub stream to go above 30.
I've tried firstly disabling any CPU intensive things. No motion detection, no smart features, no timestamp or any on screen displays, no privacy, no backlight correction or WDR.
Only Main Stream and Sub Stream 1 enabled, all other sub streams disabled and set to the lowest resolution and1fps just to see if the algorithm would let me select higher in Sub Stream 1.
Tried in both the web interface and DMSS to change the settings but alas it won't budge from maximum of 30 in sub stream 1.
I think I've exhausted trying to do this (have Main Stream (4k) and Sub Stream 1 (1080p) set to 60fps), but I know there's people here with experience of the nuances of these release notes and perhaps have an inroad to Dahua themselves to make work what they say should work?!
I can confirm the camera is running V3.100.0000000.12.R. These are the release notes:
Hope someone can help!
I've tried firstly disabling any CPU intensive things. No motion detection, no smart features, no timestamp or any on screen displays, no privacy, no backlight correction or WDR.
Only Main Stream and Sub Stream 1 enabled, all other sub streams disabled and set to the lowest resolution and1fps just to see if the algorithm would let me select higher in Sub Stream 1.
Tried in both the web interface and DMSS to change the settings but alas it won't budge from maximum of 30 in sub stream 1.
I think I've exhausted trying to do this (have Main Stream (4k) and Sub Stream 1 (1080p) set to 60fps), but I know there's people here with experience of the nuances of these release notes and perhaps have an inroad to Dahua themselves to make work what they say should work?!
I can confirm the camera is running V3.100.0000000.12.R. These are the release notes:
Hope someone can help!
Attachments
Oh gosh, I managed it using the API! At least, it'll work with the 4K at 59fps and the 1080p at 60!
For anyone who wants the hack, I made sure everything above which could use the CPU was turned off, set the main stream to 60fps, then ran this:
And it suddenly opened up the higher frame rate options in Sub Stream 1. Woop!!
Might as well follow up to express disappointment about the audio quality of the HDBW7842E1-Z-X. I placed it in the same location as one of the old HDW5231R-ZE cameras and whilst sound from the mic on the old one is bright and full, this new one is incredbly flat. I even tried piping high quality audio which I tested first going to an amp (which was crisp) but once down the line in input of the camera (with AAC 64000 and no filters), it takes all the frequency range away and there's all kinds of garbling in the encoding which make it unusable for what I needed.
After all that, it was the sound that let me down which is a real shame. I know it's asking a lot for a CCTV camera to have high quality audio but I was spoilt with some of the eyeball ones I have which are brilliant, in a literal sense. The wildlife I capture (birds, foxes, badgers) make all kinds of noises at all frequencies and the 5231s (some of them, not all, curiously) have been amazing for that.
If Dahua ever come up with a firmware update to get rid of whatever extra horrible processing is going on in a setting, that would be joyous but I doubt it given its intended application.
This camera will have to go in a location where the sound isn't important after all. which is a real shame. Anyway thought I'd feed back.
Last edited:
Yes. It calls it 'Filter Non-human Voices' in this interface as attached.
Those options also disappear when selecting the 'Line In' input with this cam. But even if I make sure it's off when the built in Mic is selected, the sound is poor, and switching to Line In makes it no better.
Attachments
Parley
Known around here
I wonder if the difference in sound has to do with the style of the camera. One is a dome while the other is a bullet.
I'll be able to show you some samples once it's installed.
Parley
Known around here
Andy, do you know if this camera will be available by the middle of next month? IPC-HFW7842H-Z4-X