dirty_pauk
n3wb
I'm fine thanks.
in this way, however, the IC cards do not work.
Unlock door Only work on RFC2833 for me
in this way, however, the IC cards do not work.
You use Asteriks as PABX server? Calling and answering calls from the intercom works fine here, but I cannot get door unlock to work. Can you post your configuration file? Would be very much appreciated!
dirty_pauk
n3wb
I use external FreePBX server with voip phone and smartphone/tablet (with voip app)
I try to make you a screenshot to make you understand (sorry my english)
P.S.
I received the VTO3211D-P4 a few days ago and I am testing configuration these days and if everything is ok I proceed with real installation
dirty_pauk
n3wb
watch the video and tell me what you need.
freePBX cofiguro via web interface, I'm impractical (tell me what the configuration files are and I'll post them)
P.S.
in SIP server configuration on VTO server type it's "asterisk".
dirty_pauk
n3wb
NEWS for unlock door by cards:
0) backup you configuration SIP (if you set it)
1) reset VTO
2) create rooms and unlock card (assign rooms to keys on layout interface if you have no backup step 0)
3) save backup UserInfo
4) restore your backup (SIP config in step 0 ....if you have it )
4b) (only if you don't have old backup step 0) >>> configure SIP server on network config
now it's working but you don't see the rooms and IC card users..
5) restore backup UserInfo (that of step 3)
now SIP works as before but you can see the rooms (you can't delete or add rooms but you can add new card/user for each room)
unlock door with card works (it only works on access control>local. Does'nt work if access control>RS485 it's enabled... maybe it only works on the second unlock by
DEE1010B interface)
2 questions:
1) how to update the firmware (config tool doesent work... there is no other way than serial uart)
2) I can access the shell (I have seen that ssh is limited)
THANKS
0) backup you configuration SIP (if you set it)
1) reset VTO
2) create rooms and unlock card (assign rooms to keys on layout interface if you have no backup step 0)
3) save backup UserInfo
4) restore your backup (SIP config in step 0 ....if you have it )
4b) (only if you don't have old backup step 0) >>> configure SIP server on network config
now it's working but you don't see the rooms and IC card users..
5) restore backup UserInfo (that of step 3)
now SIP works as before but you can see the rooms (you can't delete or add rooms but you can add new card/user for each room)
unlock door with card works (it only works on access control>local. Does'nt work if access control>RS485 it's enabled... maybe it only works on the second unlock by
DEE1010B interface)
2 questions:
1) how to update the firmware (config tool doesent work... there is no other way than serial uart)
2) I can access the shell (I have seen that ssh is limited)
THANKS
I'm having issue with this device.
I tried 2 different approach and none of them worked for video:
1) I've usd the VTO as sip server:
Can reigster my softphone and get call when button pressed but no video.
2) I've setup freepbx like dirty_pauk:
same result
The only difference between me and dirty_pauk is the firmware version.
Do you have any idea about this ? Do you know where can I get support from dahua?
I tried 2 different approach and none of them worked for video:
1) I've usd the VTO as sip server:
Can reigster my softphone and get call when button pressed but no video.
2) I've setup freepbx like dirty_pauk:
same result
The only difference between me and dirty_pauk is the firmware version.
Do you have any idea about this ? Do you know where can I get support from dahua?
dirty_pauk
n3wb
riogrande75
Pulling my weight
Anyone here, who has the western-langange pack for FW 4.3 available (General_VTO3211D_VTO32XXX-data_EngDthFrnGerItlPorSpa_P_32M_PART_V4.300)?
Would need italian language.
Would need italian language.
Hi,
I have just purchased a VTO3211D-P, version 2018-05-09 V1.000.0000001.0.R. So far I was able to check its configuration via the IE web interface and connect it to my NVR and SmartPSS, so I can see the camera image.
I am asking your assistance in solving two issues that I noticed which honestly annoy me:
Finally, is a firmware upgrade useful? How can I do it?
Thanks a lot!
I have just purchased a VTO3211D-P, version 2018-05-09 V1.000.0000001.0.R. So far I was able to check its configuration via the IE web interface and connect it to my NVR and SmartPSS, so I can see the camera image.
I am asking your assistance in solving two issues that I noticed which honestly annoy me:
- is there a way to disable the light on the front panel near the push button, which lights up in low light/darkness?
- can I disable the voice that speaks whenever one pushes the call button?
Finally, is a firmware upgrade useful? How can I do it?
Thanks a lot!
riogrande75
Pulling my weight
I suggest to upgrade to lastest firmware and MCU. Use General_VTO3211D_Eng_P_SIP_V4.300.0000000.4.R.20190306 and a language pack like General_VTO32XXX-data_EngTurSlkPldHgrFinCzeBul_P_32M_SIP_PART_V4.300.0000004.0.R.20190629.
Then you have the opportunity to set language to your preferred one and to deactivate voice prompts completely.
Also the light behaviour can be modified.
Then you have the opportunity to set language to your preferred one and to deactivate voice prompts completely.
Also the light behaviour can be modified.
Dear All,
I just purchased this VTO3211D-P (single button) to act as a video doorbell in my own house. Works great, setup was only a little bit confusing thanks to the lot of contribution from you guysI can open with multiple mifar keyfobs, I can unlock from WAN, and I get idmss plus notifications to 3 iOS device at the same time via p2p, even on WAN, without problem. I do not have a VTH, I have an iPad in the house which acts as a HomeKit hub.
I'm seeking for a little advice on integrating the device into Homekit, via Homebridge. I have a synology NAS, running Homebridhe, and I already have integrated several Dahua IPC-s into Homekit this way, via ffmpeg plugin and remote streaming protocol. During the integration, in the plugin configuration I need to use two URLs, one for the rtps stream link, and for a snapshot image url (Homekit only refreshes snapshots when user interacts with Apple Home app, and stream is only called when you click on the image, thus reducing streaming load on the camera).
for this VTO I can access the rtsp stream via http easily (btw, I only found this method working to integrate the VTO into a Dahua NVR4108 to record camera along with the other IPC, does anyone know a better way??), but I can't find any snapshot image url, the usual snapshot.cgi url does not work.
Does any of you know any way, to get a httpc call from the camera ANYTIME, which snaps an actual photo, and sends it over http via LAN?
Also, one comment from a fellow member riogrande got really caught my eyes, by saying integrating MQTT topic sending into the firmware, that could be also very very interesting, to make further automations via Homebridge, any thoughts on that?
Thanks in advance!!
Sorry for the late reply,
I've got mine working with home bridge with the following address:
"source": "-re -i rtsp:/user
assword@192.168..:554/cam/realmonitor?channel=1&subtype=1","stillImageSource": "-i http://user
assword@192.168.*.*/cgi-bin/snapshot.cgi?",Ciao Abbiamo lo stesso citofono, io ho la versione 1.0 dato che non so nemmno se riesco a fare l'ugrade alla versione 4.0 dato che mi si blocca al 50 % volevo sapere se hai notato delle funzioni nuove, ad esempio la telecamera è ancroa bloccata a 720P ?
dirty_pauk
n3wb
Ciao,
Io l'ho lasciato con la versione che mi è arrivato.
Ti allego quello che mi hai chiesto
Hi all,
I have just purchased a VTO3211D-P2 and VTH5221DW-C.
Everything is ok when I ring the VTH answers but impossible to receive push notifications in mobile devices (IDMSS PLUS and DMSS) however I have activated push notifications in the applications menu.
Is there anything to activate in the VTO options?
Thanks
I have just purchased a VTO3211D-P2 and VTH5221DW-C.
Everything is ok when I ring the VTH answers but impossible to receive push notifications in mobile devices (IDMSS PLUS and DMSS) however I have activated push notifications in the applications menu.
Is there anything to activate in the VTO options?
Thanks
Hi, where do you buy it?
Ciao, dove l'hai acquistato? che ne pensi di questo che ho addocchiato a 1 tasto?
120.0US $ |Dh Logo Multi-language Vto3211d-p/p2/p4 Poe(802.3af) Ip Metal Villa Doorbell ,door Phone,doorbell,ip Video Intercom,sip Firmware - Video Intercom - AliExpress
Smarter Shopping, Better Living! Aliexpress.com
s.click.aliexpress.com